lkml.org 
[lkml]   [2018]   [May]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 3/3] arm64: dts: renesas: draak: Describe HDMI input
Hi Jacopo,

Thanks for your patch.

On 2018-05-16 15:42:09 +0200, Jacopo Mondi wrote:
> Describe HDMI input connector and ADV7612 HDMI decoder installed on
> R-Car Gen3 Draak board.
>
> The video signal routing to the HDMI decoder to the video input interface
> VIN4 is multiplexed with CVBS input path, and enabled/disabled through
> on-board switches SW-49, SW-50, SW-51 and SW-52.
>
> As the default board switches configuration connects CVBS input to VIN4,
> leave the HDMI decoder unconnected in DTS.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

I'm not sure we have a policy about describing hardware which can't be
used without flipping switches. I have no opinion on if we should do
that or not I leave that to others, but for the change itself.

Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

I think it's good we describe it as it's part of the Draak board itself
and not an expansion board which we have seen a lot of :-) Maybe even
add a commented out line in the adv7612 port@2 which hints which VIN
this is connected to if the switches are flipped?

> ---
> arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 38 ++++++++++++++++++++++++++
> 1 file changed, 38 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
> index 9aba28f..ea99dc9 100644
> --- a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
> +++ b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
> @@ -59,6 +59,17 @@
> };
> };
>
> + hdmi-in {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&adv7612_in>;
> + };
> + };
> + };
> +
> memory@48000000 {
> device_type = "memory";
> /* first 128MB is reserved for secure area. */
> @@ -170,6 +181,33 @@
> };
> };
> };
> +
> + hdmi-decoder@4c {
> + compatible = "adi,adv7612";
> + reg = <0x4c>;
> + default-input = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + adv7612_in: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + adv7612_out: endpoint {
> + pclk-sample = <0>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + };
> + };
> + };
> + };
> };
>
> &i2c1 {
> --
> 2.7.4
>

--
Regards,
Niklas Söderlund

\
 
 \ /
  Last update: 2018-05-17 00:24    [W:0.082 / U:2.868 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site