lkml.org 
[lkml]   [2018]   [Apr]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/4] gpio: pca953x: add register definitions for pcal6524 and fix address calculation
Date
PCAL chips ("L" seems to stand for "latched") have additional
registers starting at address 0x40 to control the latches,
interrupt mask, pull-up and pull down etc.

The constants are so far defined in a way that they fit for
the pcal9555a when shifted by the number of banks, i.e. multiplied
by 2.

Now the pcal6524 has 3 banks which means the relative offset
must be multiplied by 4 which gives a wrong result if not done
carefully, since the base offset is already included in the offset.

For the basic registers shared with all pca93xx/tca64xx chips
there is no such offset.

Therefore, we add code to adjust the register number for exended
registers to the 24 bit accessor functions.

And we add additional register offset constants (not yet used by
the driver code) which are specific to the pcal6524.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
drivers/gpio/gpio-pca953x.c | 50 ++++++++++++++++++++++++++++++---------------
1 file changed, 34 insertions(+), 16 deletions(-)

diff --git a/drivers/gpio/gpio-pca953x.c b/drivers/gpio/gpio-pca953x.c
index 4a075619b93e..022307d328ff 100644
--- a/drivers/gpio/gpio-pca953x.c
+++ b/drivers/gpio/gpio-pca953x.c
@@ -25,25 +25,35 @@

#include <asm/unaligned.h>

-#define PCA953X_INPUT 0
-#define PCA953X_OUTPUT 1
-#define PCA953X_INVERT 2
-#define PCA953X_DIRECTION 3
+#define PCA953X_INPUT 0x0
+#define PCA953X_OUTPUT 0x1
+#define PCA953X_INVERT 0x2
+#define PCA953X_DIRECTION 0x3

#define REG_ADDR_AI 0x80

-#define PCA957X_IN 0
-#define PCA957X_INVRT 1
-#define PCA957X_BKEN 2
-#define PCA957X_PUPD 3
-#define PCA957X_CFG 4
-#define PCA957X_OUT 5
-#define PCA957X_MSK 6
-#define PCA957X_INTS 7
-
-#define PCAL953X_IN_LATCH 34
-#define PCAL953X_INT_MASK 37
-#define PCAL953X_INT_STAT 38
+#define PCA957X_IN 0x00
+#define PCA957X_INVRT 0x01
+#define PCA957X_BKEN 0x02
+#define PCA957X_PUPD 0x03
+#define PCA957X_CFG 0x04
+#define PCA957X_OUT 0x05
+#define PCA957X_MSK 0x06
+#define PCA957X_INTS 0x07
+
+#define PCAL953X_OUT_STRENGTH 0x20
+#define PCAL953X_IN_LATCH 0x22
+#define PCAL953X_PULL_EN 0x23
+#define PCAL953X_PULL_SEL 0x24
+#define PCAL953X_INT_MASK 0x25
+#define PCAL953X_INT_STAT 0x26
+#define PCAL953X_OUT_CONF 0x27
+
+#define PCAL6524_INT_EDGE 0x28
+#define PCAL6524_INT_CLR 0x2a
+#define PCAL6524_IN_STATUS 0x2b
+#define PCAL6524_OUT_INDCONF 0x2c
+#define PCAL6524_DEBOUNCE 0x2d

#define PCA_GPIO_MASK 0x00FF
#define PCA_INT 0x0100
@@ -208,6 +218,10 @@ static int pca953x_write_regs_24(struct pca953x_chip *chip, int reg, u8 *val)
{
int bank_shift = fls((chip->gpio_chip.ngpio - 1) / BANK_SZ);

+ /* adjust register address for pcal6524 */
+ if (reg >= PCAL953X_OUT_STRENGTH)
+ reg -= PCAL953X_OUT_STRENGTH >> 1;
+
return i2c_smbus_write_i2c_block_data(chip->client,
(reg << bank_shift) | REG_ADDR_AI,
NBANK(chip), val);
@@ -250,6 +264,10 @@ static int pca953x_read_regs_24(struct pca953x_chip *chip, int reg, u8 *val)
{
int bank_shift = fls((chip->gpio_chip.ngpio - 1) / BANK_SZ);

+ /* adjust register address for pcal6524 */
+ if (reg >= PCAL953X_OUT_STRENGTH)
+ reg -= PCAL953X_OUT_STRENGTH >> 1;
+
return i2c_smbus_read_i2c_block_data(chip->client,
(reg << bank_shift) | REG_ADDR_AI,
NBANK(chip), val);
--
2.12.2
\
 
 \ /
  Last update: 2018-04-10 18:09    [W:0.086 / U:0.440 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site