lkml.org 
[lkml]   [2018]   [Mar]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 2/8] [PATCH 2/8] Documentations: dt-bindings: Add a document of PECI adapter driver for Aspeed AST24xx/25xx SoCs
From
Date
Hi Pavel,

Thanks for sharing your time on reviewing it. Please see my answers inline.

-Jae

On 3/6/2018 4:40 AM, Pavel Machek wrote:
> Hi!
>
>> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
>> ---
>> .../devicetree/bindings/peci/peci-aspeed.txt | 73 ++++++++++++++++++++++
>> 1 file changed, 73 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/peci/peci-aspeed.txt
>>
>> diff --git a/Documentation/devicetree/bindings/peci/peci-aspeed.txt b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
>> new file mode 100644
>> index 000000000000..8a86f346d550
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
>> @@ -0,0 +1,73 @@
>> +Device tree configuration for PECI buses on the AST24XX and AST25XX SoCs.
>
> Are these SoCs x86-based?
>

Yes, these are ARM SoCs. Please see Andrew's answer as well.

>> +Required properties:
>> +- compatible
>> + "aspeed,ast2400-peci" or "aspeed,ast2500-peci"
>> + - aspeed,ast2400-peci: Aspeed AST2400 family PECI controller
>> + - aspeed,ast2500-peci: Aspeed AST2500 family PECI controller
>> +
>> +- reg
>> + Should contain PECI registers location and length.
>
> Other dts documents put it on one line, reg: Should contain ...
>
>> +- clock_frequency
>> + Should contain the operation frequency of PECI hardware module.
>> + 187500 ~ 24000000
>
> specify this is Hz?
>

I'll add a description. Thanks!

>> +- rd-sampling-point
>> + Read sampling point selection. The whole period of a bit time will be
>> + divided into 16 time frames. This value will determine which time frame
>> + this controller will sample PECI signal for data read back. Usually in
>> + the middle of a bit time is the best.
>
> English? "This value will determine when this controller"?
>

Could I change it like below?:

"This value will determine in which time frame this controller samples
PECI signal for data read back"

>> + 0 ~ 15 (default: 8)
>> +
>> +- cmd_timeout_ms
>> + Command timeout in units of ms.
>> + 1 ~ 60000 (default: 1000)
>> +
>> +Example:
>> + peci: peci@1e78b000 {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0x1e78b000 0x60>;
>> +
>> + peci0: peci-bus@0 {
>> + compatible = "aspeed,ast2500-peci";
>> + reg = <0x0 0x60>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <15>;
>> + clocks = <&clk_clkin>;
>> + clock-frequency = <24000000>;
>> + msg-timing-nego = <1>;
>> + addr-timing-nego = <1>;
>> + rd-sampling-point = <8>;
>> + cmd-timeout-ms = <1000>;
>> + };
>> + };
>> \ No newline at end of file
>

\
 
 \ /
  Last update: 2018-03-06 20:06    [W:0.129 / U:0.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site