lkml.org 
[lkml]   [2018]   [Mar]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] usb: dwc3: Prevent indefinite sleep in _dwc3_set_mode during suspend/resume
From
Date
Felipe,

On 05/03/18 10:49, Felipe Balbi wrote:
>
> Hi,
>
> Roger Quadros <rogerq@ti.com> writes:
>>> Roger Quadros <rogerq@ti.com> writes:
>>>> In the following test we get stuck by sleeping forever in _dwc3_set_mode()
>>>> after which dual-role switching doesn't work.
>>>>
>>>> On dra7-evm's dual-role port,
>>>> - Load g_zero gadget driver and enumerate to host
>>>> - suspend to mem
>>>> - disconnect USB cable to host and connect otg cable with Pen drive in it.
>>>> - resume system
>>>> - we sleep indefinitely in _dwc3_set_mode due to.
>>>> dwc3_gadget_exit()->usb_del_gadget_udc()->udc_stop()->
>>>> dwc3_gadget_stop()->wait_event_lock_irq()
>>>>
>>>> Let's clear the DWC3_EP_END_TRANSFER_PENDING flag on all endpoints
>>>> so we don't wait in dwc3_gadget_stop().
>>>>
>>>> Signed-off-by: Roger Quadros <rogerq@ti.com>
>>>> ---
>>>> drivers/usb/dwc3/gadget.c | 14 ++++++++++++++
>>>> 1 file changed, 14 insertions(+)
>>>>
>>>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
>>>> index 2bda4eb..0a360da 100644
>>>> --- a/drivers/usb/dwc3/gadget.c
>>>> +++ b/drivers/usb/dwc3/gadget.c
>>>> @@ -3273,6 +3273,20 @@ int dwc3_gadget_init(struct dwc3 *dwc)
>>>>
>>>> void dwc3_gadget_exit(struct dwc3 *dwc)
>>>> {
>>>> + int epnum;
>>>> + unsigned long flags;
>>>> +
>>>> + spin_lock_irqsave(&dwc->lock, flags);
>>>> + for (epnum = 2; epnum < DWC3_ENDPOINTS_NUM; epnum++) {
>>>> + struct dwc3_ep *dep = dwc->eps[epnum];
>>>> +
>>>> + if (!dep)
>>>> + continue;
>>>> +
>>>> + dep->flags &= ~DWC3_EP_END_TRANSFER_PENDING;
>>>> + }
>>>> + spin_unlock_irqrestore(&dwc->lock, flags);
>>>> +
>>>> usb_del_gadget_udc(&dwc->gadget);
>>>> dwc3_gadget_free_endpoints(dwc);
>>>
>>> free endpoints is a better place for this. It's already going to free
>>> the memory anyway. Might as well clear all flags to 0 there.
>>>
>>
>> But it won't solve the deadlock issue. Since dwc3_gadget_free_endpoints()
>> is called after usb_del_gadget_udc() and the deadlock happens when
>>
>> usb_del_gadget_udc()->udc_stop()->dwc3_gadget_stop()->wait_event_lock_irq()
>>
>> and DWC3_EP_END_TRANSFER_PENDING flag is set.
>
> indeed. Iterating twice over the entire endpoint list seems
> wasteful. Perhaps we just shouldn't wait when removing the UDC since
> that's essentially what this patch will do, right? If you clear the flag
> before calling ->udc_stop(), this means the loop in dwc3_gadget_stop()
> will do nothing. Might as well remove it.
>

This means that we will never wait for DWC3_EP_END_TRANSFER_PENDING to clear
in dwc3_gadget_stop() like we used to. This is perfectly fine, right?

It makes sense to me as dwc3_gadget_stop() calls __dwc3_gadget_stop() which
masks all interrupts and nobody will ever clear that flag if it was set.

And there is no point in clearing the DWC3_EP_END_TRANSFER_PENDING flag
in dwc3_gadget_free_endpoints() since we're freeing the dwc3_ep memory there.

dwc3_gadget_init_endpoints() will start with a clean slate.

--
cheers,
-roger

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

\
 
 \ /
  Last update: 2018-03-05 10:46    [W:0.087 / U:0.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site