lkml.org 
[lkml]   [2018]   [Mar]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v2 3/8] arm64: zynqmp: Add support for Xilinx zcu102
On Fri, Feb 23, 2018 at 03:40:25PM +0100, Michal Simek wrote:
> This patch is adding revA, revB and rev1.0. There are also other
> revisions between which should be backward compatible with previous
> versions. Unfortunately all revs are still in use.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v2:
> - Remove i2c mw u-boot commands
> - Use i2c-mux instead of i2cswitch
> - Use clock generator without numbers.
> - Use dash in node name zcu102 rev1.0
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 5 +
> arch/arm64/boot/dts/xilinx/Makefile | 3 +
> .../arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 36 ++
> arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 550 +++++++++++++++++++++
> arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts | 42 ++
> 5 files changed, 636 insertions(+)
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts

Reviewed-by: Rob Herring <robh@kernel.org>

but...


> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> new file mode 100644
> index 000000000000..ed3cc684931f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> @@ -0,0 +1,42 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * dts file for Xilinx ZynqMP ZCU102 RevB
> + *
> + * (C) Copyright 2016 - 2018, Xilinx, Inc.
> + *
> + * Michal Simek <michal.simek@xilinx.com>
> + */
> +
> +#include "zynqmp-zcu102-revA.dts"
> +
> +/ {
> + model = "ZynqMP ZCU102 RevB";
> + compatible = "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> +};
> +
> +&gem3 {
> + phy-handle = <&phyc>;
> + phyc: phy@c {
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + };
> + /* Cleanup from RevA */
> + /delete-node/ phy@21;
> +};
> +
> +/* Different qspi 512Mbit version */
Stray comment

> +
> +/* Fix collision with u61 */
> +&i2c0 {
> + i2cswitch@75 {

Missed this name.

This probably creates a new node rather than going into the existing
tree. If this compiles, we should fix it to not allow the same
unit-address twice.

> + i2c@2 {
> + max15303@1b { /* u8 */
> + compatible = "maxim,max15303";
> + reg = <0x1b>;
> + };
> + /delete-node/ max15303@20;
> + };
> + };
> +};
> --
> 1.9.1
>

\
 
 \ /
  Last update: 2018-03-02 17:48    [W:0.132 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site