lkml.org 
[lkml]   [2018]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 4/9] dt-bindings: gpio: Add gpio nodes for Actions S900 SoC
On Fri, Mar 09, 2018 at 10:43:40AM +0530, Manivannan Sadhasivam wrote:
> Add gpio nodes for Actions Semi S900 SoC.
>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
> .../devicetree/bindings/gpio/actions,owl-gpio.txt | 90 ++++++++++++++++++++++
> 1 file changed, 90 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt b/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> new file mode 100644
> index 000000000000..ad7d32ce2abe
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> @@ -0,0 +1,90 @@
> +* Actions Semi OWL GPIO controller bindings
> +
> +The GPIOs are organized as individual banks/ports with variable number
> +of GPIOs. Each bank is represented as an individual GPIO controller.
> +
> +Required properties:
> +- compatible : Should be "actions,s900-gpio"
> +- reg : Address and range of the GPIO controller registers.
> +- gpio-controller : Marks the device node as a GPIO controller.
> +- #gpio-cells : Should be <2>. The first cell is the gpio number
> + and the second cell is used to specify optional
> + parameters.
> +- ngpios : Specifies the number of GPIO lines.
> +- interrupt-controller : Marks the device node as an interrupt controller.
> +- #interrupt-cells : Specifies the number of cells needed to encode an
> + interrupt. Shall be set to 2. The first cell
> + defines the interrupt number, the second encodes
> + the trigger flags described in
> + bindings/interrupt-controller/interrupts.txt
> +
> +Optional properties:
> +- gpio-ranges : Mapping between GPIO and pinctrl
> +
> +Examples:
> +
> + gpioa: gpio@e01b0000 {
> + compatible = "actions,s900-gpio";
> + reg = <0x0 0xe01b0000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pinctrl 0 0 32>;
> + ngpios = <32>;

This is only needed if the number of gpios is reduced for some reason
such as not pinned out. IOW, 32 is implied because that's the size of
each bank.

> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpiob: gpio@e01b000c {
> + compatible = "actions,s900-gpio";
> + reg = <0x0 0xe01b000c 0x0 0x1000>;

Due to the sizes, these are still overlapping.

Rob

> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pinctrl 0 32 32>;
> + ngpios = <32>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };

\
 
 \ /
  Last update: 2018-03-18 13:53    [W:0.101 / U:0.488 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site