lkml.org 
[lkml]   [2018]   [Feb]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v11 2/7] PCI/AER: factor out error reporting from AER
On Mon, Feb 26, 2018 at 11:02:50AM +0530, poza@codeaurora.org wrote:
> On 2018-02-24 05:12, Bjorn Helgaas wrote:
> > On Fri, Feb 23, 2018 at 01:53:59PM +0530, Oza Pawandeep wrote:

> > > * handle_error_source - handle logging error into an event log
> > > diff --git a/drivers/pci/pcie/pcie-err.c b/drivers/pci/pcie/pcie-err.c
> > > new file mode 100644
> > > index 0000000..fcd5add
> > > --- /dev/null
> > > +++ b/drivers/pci/pcie/pcie-err.c
> > > @@ -0,0 +1,334 @@
> > > +// SPDX-License-Identifier: GPL-2.0
> > > +/*
> > > + * This file implements the error recovery as a core part of PCIe
> > > error reporting.
> > > + * When a PCIe error is delivered, an error message will be
> > > collected and printed
> > > + * to console, then, an error recovery procedure will be executed
> > > by following
> > > + * the PCI error recovery rules.
> >
> > Wrap this so it fits in 80 columns.
>
> I thought of keeping the way it was before (hence did not change it)
> I would change it now.

The original text fit in 80 columns, but you changed the text a little
bit as part of making this code more generic, which made it not fit
anymore. Ideally I would leave the text the same in this patch that
only moves code, then update the text (and rewrap it) in the patch
that makes the code more generic.

> > > +static pci_ers_result_t reset_link(struct pci_dev *dev)
> > > +{
> > > + struct pci_dev *udev;
> > > + pci_ers_result_t status;
> > > + struct pcie_port_service_driver *driver = NULL;
> > > +
> > > + if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) {
> > > + /* Reset this port for all subordinates */
> > > + udev = dev;
> > > + } else {
> > > + /* Reset the upstream component (likely downstream port) */
> > > + udev = dev->bus->self;
> > > + }
> > > +
> > > +#if IS_ENABLED(CONFIG_PCIEAER)
> >
> > AER can't be a module, so you can use just:
> >
> > #ifdef CONFIG_PCIEAER
> >
> > This ifdef should be added in the patch where you add a caller from
> > non-AER
> > code. This patch should only move code, not change it.
>
> ok, it can remain unchanged. but reset_link() is called by
> pcie_do_recovery()
> and pcie_do_recovery can be called by various agents such as AER, DPC.
> so let us say if DPC calls pcie_do_recovery, then DPC has no way of knowing
> that AER is enabled or not.
> in fact it should not know, but err.c/reset_link() should take care somehow.

If all you're doing is moving code, the functionality isn't changing
and you shouldn't need to add the ifdef. At the point where you add a
new caller and the #ifdef becomes necessary, you can add it there.
Then it will make sense because we can connect the ifdef with the need
for it.

> I can make it a separate patch to do #ifdef CONFIG_PCIEAER inside
> reset_link()
> or
> I can add severity parameter in reset_link() so based on severity it can
> find the service.
>
> but I think you have comment to unify the find_aer_service and
> find_dpc_service into a pcie_find_service (routine)
> so I will see how I can club and take care of this comment. [without the
> need of #ifdef]

\
 
 \ /
  Last update: 2018-02-26 21:56    [W:0.656 / U:0.196 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site