Messages in this thread | | | From | Andy Shevchenko <> | Date | Fri, 16 Feb 2018 16:40:36 +0200 | Subject | Re: [PATCH v2] rtc: isl12026: Add driver. |
| |
On Thu, Feb 15, 2018 at 9:01 PM, David Daney <ddaney@caviumnetworks.com> wrote: > On 02/15/2018 04:45 AM, Andy Shevchenko wrote: >> On Wed, Feb 14, 2018 at 2:55 AM, David Daney <david.daney@cavium.com> >> wrote: >>> >>> The ISL12026 is a combination RTC and EEPROM device with I2C >>> interface. The standard RTC driver interface is provided. The EEPROM >>> is accessed via the NVMEM interface via the "eeprom0" directory in the >>> sysfs entry for the device.
>>> + /* 2 bytes of address, most significant first */ >>> + addr[0] = (offset >> 8) & 0xff; >>> + addr[1] = offset & 0xff; >> >> >> Consider to drop '& 0xff', they are pointless (you have u8 type). > > > Generated code is the same, but the intent of the code is less clear when > the explicit masking is removed. Never the less, since this seems to be > impeding progress, I will remove it.
You can use the following:
addr[0] = offset >> 8; addr[1] = offset >> 0;
>>> + bool set_bsw, set_sbib; >>> +
>>> + ret = of_property_read_u32(client->dev.of_node, >>> + "isil,pwr-bsw", &bsw_val); >>> + set_bsw = (ret == 0);
>> Which is not fully correct. Better to do
> I think it is correct. The properties are optional, so it it perfectly fine > for of_property_read_u32() to fail. If it fails, we simply keep the current > value. I will add comments to document the intended logic.
OK.
>> set_bsw = of_property_present();
> There are no occurrences of "of_property_present" in my source tree.
Ah, indeed.
>> ret = of_property_read...(); >> if (ret) >> return ret;
What about then
set_bsw = of_property_read_bool();
set_sbid = ...
if (!x && !y) return ...
...
if (x) {
}
>> >>> + >>> + ret = of_property_read_u32(client->dev.of_node, >>> + "isil,pwr-sbib", &sbib_val); >>> + set_sbib = (ret == 0); >> >> >> Ditto.
>>> + if (set_bsw) { >>> + if (bsw_val) >>> + requested_pwr |= ISL12026_REG_PWR_BSW; >>> + else >>> + requested_pwr &= ~ISL12026_REG_PWR_BSW; >>> + } >> >> >> Undefined state if no value?
> It is defined. See above.
It's opaque. Depends on firmware settings, boot loader, etc.
>>> +#ifdef CONFIG_OF >> Remove this ugly #ifdef. Your driver OF only one.
> The driver doesn't require OF.
> By removing the #if (which I will do), the > size of the module may be bloated in the non-OF case. If anybody cares > about this, they can add back the #if.
Nobody.
>>> +static const struct of_device_id isl12026_dt_match[] = { >>> + { .compatible = "isil,isl12026" }, >>> + { }, >>> +}; >>> +MODULE_DEVICE_TABLE(of, isl12026_dt_match);
>>> + .of_match_table = of_match_ptr(isl12026_dt_match), >> Drop of_match_ptr().
> Best to keep it so that the non-OF case is correctly handled.
If you drop above ifdef, you need to drop this macro. And code bloat is not big.
Btw, driver since ->probe_new() is become OF/ACPI only, so, otherwise there will be no way to enumerate.
-- With Best Regards, Andy Shevchenko
| |