lkml.org 
[lkml]   [2018]   [Feb]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 0/6] IR support for A83T
Hi Philipp,

On Mon, Feb 12, 2018 at 12:00:02PM +0100, Philipp Rossak wrote:
> On 30.01.2018 18:46, Philipp Rossak wrote:
> > This patch series adds support for the sunxi A83T ir module and enhances
> > the sunxi-ir driver. Right now the base clock frequency for the ir driver
> > is a hard coded define and is set to 8 MHz.
> > This works for the most common ir receivers. On the Sinovoip Bananapi M3
> > the ir receiver needs, a 3 MHz base clock frequency to work without
> > problems with this driver.
> >
> > This patch series adds support for an optinal property that makes it able
> > to override the default base clock frequency and enables the ir interface
> > on the a83t and the Bananapi M3.
> >
> > changes since v4:
> > * rename cir pin from cir_pins to r_cir_pin
> > * drop unit-adress from r_cir_pin
> > * add a83t compatible to the cir node
> > * move muxing options to dtsi
> > * rename cir label and reorder it in the bananpim3.dts file
> >
> > changes since v3:
> > * collecting all acks & reviewd by
> > * fixed typos
> >
> > changes since v2:
> > * reorder cir pin (alphabetical)
> > * fix typo in documentation
> >
> > changes since v1:
> > * fix typos, reword Documentation
> > * initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
> > * change dev_info() to dev_dbg()
> > * change naming to cir* in dts/dtsi
> > * Added acked Ackedi-by to related patch
> > * use whole memory block instead of registers needed + fix for h3/h5
> >
> > changes since rfc:
> > * The property is now optinal. If the property is not available in
> > the dtb the driver uses the default base clock frequency.
> > * the driver prints out the the selected base clock frequency.
> > * changed devicetree property from base-clk-frequency to clock-frequency
> >
> > Regards,
> > Philipp
> >
> > Philipp Rossak (6):
> > media: rc: update sunxi-ir driver to get base clock frequency from
> > devicetree
> > media: dt: bindings: Update binding documentation for sunxi IR
> > controller
> > arm: dts: sun8i: a83t: Add the cir pin for the A83T
> > arm: dts: sun8i: a83t: Add support for the cir interface
> > arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller
> > arm: dts: sun8i: h3-h5: ir register size should be the whole memory
> > block
> >
> > Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++
> > arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 5 +++++
> > arch/arm/boot/dts/sun8i-a83t.dtsi | 18 ++++++++++++++++++
> > arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
> > drivers/media/rc/sunxi-cir.c | 19 +++++++++++--------
> > 5 files changed, 38 insertions(+), 9 deletions(-)
> >
>
> RC1 is now out, thus I would like to ask you to have a look at this patch
> series again. Some patches still miss an acked-by. It would be nice if we
> could schedule this for v4.17.

Just resend it, this will send pretty much the same signal :)

Maxime

--
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
http://bootlin.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2018-02-13 08:59    [W:0.064 / U:1.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site