lkml.org 
[lkml]   [2018]   [Feb]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v3 3/5] [RFT] ARM: dts: wheat: Fix ADV7513 address usage
Date
Hi Kieran,

Thank you for the patch.

On Tuesday, 13 February 2018 00:07:51 EET Kieran Bingham wrote:
> From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
>
> The r8a7792 Wheat board has two ADV7513 devices sharing a single i2c
> bus, however in low power mode the ADV7513 will reset it's slave maps to
> use the hardware defined default addresses.
>
> The ADV7511 driver was adapted to allow the two devices to be registered
> correctly - but it did not take into account the fault whereby the
> devices reset the addresses.
>
> This results in an address conflict between the device using the default
> addresses, and the other device if it is in low-power-mode.
>
> Repair this issue by moving both devices away from the default address
> definitions.
>
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
> v2:
> - Addition to series
>
> v3:
> - Split map register addresses into individual declarations.
>
> arch/arm/boot/dts/r8a7792-wheat.dts | 12 ++++++++++--
> 1 file changed, 10 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts
> b/arch/arm/boot/dts/r8a7792-wheat.dts index b9471b67b728..42fff8837eab
> 100644
> --- a/arch/arm/boot/dts/r8a7792-wheat.dts
> +++ b/arch/arm/boot/dts/r8a7792-wheat.dts
> @@ -240,9 +240,16 @@
> status = "okay";
> clock-frequency = <400000>;
>
> + /*
> + * The adv75xx resets its addresses to defaults during low power power
> + * mode. Because we have two ADV7513 devices on the same bus, we must
> + * change both of them away from the defaults so that they do not
> + * conflict.
> + */
> hdmi@3d {
> compatible = "adi,adv7513";
> - reg = <0x3d>;
> + reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
> + reg-names = "main", "cec", "edid", "packet";
>
> adi,input-depth = <8>;
> adi,input-colorspace = "rgb";
> @@ -272,7 +279,8 @@
>
> hdmi@39 {
> compatible = "adi,adv7513";
> - reg = <0x39>;
> + reg = <0x39>, <0x29>, <0x49>, <0x59>;
> + reg-names = "main", "cec", "edid", "packet";
>
> adi,input-depth = <8>;
> adi,input-colorspace = "rgb";

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2018-02-13 13:11    [W:0.082 / U:1.524 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site