lkml.org 
[lkml]   [2018]   [Feb]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v3 1/5] dt-bindings: media: adv7604: Add support for i2c_new_secondary_device
Date
Hi Kieran,

Thank you for the patch.

On Tuesday, 13 February 2018 00:07:49 EET Kieran Bingham wrote:
> From: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
>
> The ADV7604 has thirteen 256-byte maps that can be accessed via the main
> I²C ports. Each map has it own I²C address and acts as a standard slave
> device on the I²C bus.
>
> Extend the device tree node bindings to be able to override the default
> addresses so that address conflicts with other devices on the same bus
> may be resolved at the board description level.
>
> Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
> [Kieran: Re-adapted for mainline]
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> Reviewed-by: Rob Herring <robh@kernel.org>

Nitpicking, I might not mention i2c_new_secondary_device in the subject, as
this is a DT bindings change. I don't mind too much though, as long as the
bindings themselves don't contain Linux-specific information, and they don't,
so

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
> Based upon the original posting :
> https://lkml.org/lkml/2014/10/22/469
>
> v2:
> - DT Binding update separated from code change
> - Minor reword to commit message to account for DT only change.
> - Collected Rob's RB tag.
>
> v3:
> - Split map register addresses into individual declarations.
>
> .../devicetree/bindings/media/i2c/adv7604.txt | 18
> ++++++++++++++++-- 1 file changed, 16 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index
> 9cbd92eb5d05..ebb5f070c05b 100644
> --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
> @@ -13,7 +13,11 @@ Required Properties:
> - "adi,adv7611" for the ADV7611
> - "adi,adv7612" for the ADV7612
>
> - - reg: I2C slave address
> + - reg: I2C slave addresses
> + The ADV76xx has up to thirteen 256-byte maps that can be accessed via
> the + main I²C ports. Each map has it own I²C address and acts as a
> standard + slave device on the I²C bus. The main address is mandatory,
> others are + optional and revert to defaults if not specified.
>
> - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
> detection pins, one per HDMI input. The active flag indicates the GPIO
> @@ -35,6 +39,11 @@ Optional Properties:
>
> - reset-gpios: Reference to the GPIO connected to the device's reset pin.
> - default-input: Select which input is selected after reset.
> + - reg-names : Names of maps with programmable addresses.
> + It can contain any map needing a non-default address.
> + Possible maps names are :
> + "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe",
> + "rep", "edid", "hdmi", "test", "cp", "vdp"
>
> Optional Endpoint Properties:
>
> @@ -52,7 +61,12 @@ Example:
>
> hdmi_receiver@4c {
> compatible = "adi,adv7611";
> - reg = <0x4c>;
> + /*
> + * The edid page will be accessible @ 0x66 on the i2c bus. All
> + * other maps will retain their default addresses.
> + */
> + reg = <0x4c>, <0x66>;
> + reg-names "main", "edid";
>
> reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
> hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;


--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2018-02-13 13:07    [W:0.070 / U:2.120 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site