lkml.org 
[lkml]   [2018]   [Jan]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH v6 4/6] can: m_can: Support higher speed CAN-FD bitrates
From
Date
On 12/22/2017 02:31 PM, Faiz Abbas wrote:
> From: Franklin S Cooper Jr <fcooper@ti.com>
>
> During test transmitting using CAN-FD at high bitrates (> 2 Mbps)
> would fail. Scoping the signals I noticed that only a single bit
> was being transmitted and with a bit more investigation realized the actual
> MCAN IP would go back to initialization mode automatically.
>
> It appears this issue is due to the MCAN needing to use the Transmitter
> Delay Compensation Mode with the correct value for the transmitter delay
> compensation offset (tdco). What impacts the tdco value isn't 100% clear
> but to calculate it you use an equation defined in the MCAN User's Guide.
>
> The user guide mentions that this register needs to be set based on clock
> values, secondary sample point and the data bitrate. One of the key
> variables that can't automatically be determined is the secondary
> sample point (ssp). This ssp is similar to the sp but is specific to this
> transmitter delay compensation mode. The guidelines for configuring
> ssp is rather vague but via some CAN test it appears for DRA76x that putting
> the value same as data sampling point works.
>
> The CAN-CIA's "Bit Time Requirements for CAN FD" paper presented at
> the International CAN Conference 2013 indicates that this TDC mode is
> only needed for data bit rates above 2.5 Mbps. Therefore, only enable
> this mode when the data bit rate is above 2.5 Mbps.
>
> Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
> ---
> drivers/net/can/m_can/m_can.c | 41 ++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 40 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
> index 53e764f..371ffc1 100644
> --- a/drivers/net/can/m_can/m_can.c
> +++ b/drivers/net/can/m_can/m_can.c
> @@ -127,6 +127,12 @@ enum m_can_mram_cfg {
> #define DBTP_DSJW_SHIFT 0
> #define DBTP_DSJW_MASK (0xf << DBTP_DSJW_SHIFT)
>
> +/* Transmitter Delay Compensation Register (TDCR) */
> +#define TDCR_TDCO_SHIFT 8
> +#define TDCR_TDCO_MASK (0x7F << TDCR_TDCO_SHIFT)
> +#define TDCR_TDCF_SHIFT 0
> +#define TDCR_TDCF_MASK (0x7F << TDCR_TDCF_SHIFT)
> +
> /* Test Register (TEST) */
> #define TEST_LBCK BIT(4)
>
> @@ -991,7 +997,8 @@ static int m_can_set_bittiming(struct net_device *dev)
> const struct can_bittiming *bt = &priv->can.bittiming;
> const struct can_bittiming *dbt = &priv->can.data_bittiming;
> u16 brp, sjw, tseg1, tseg2;
> - u32 reg_btp;
> + u32 reg_btp, tdco, ssp;

Please move the tdco and the ssp into "if (dbt->bitrate > 2500000)" scope.

Initialize "reg_btp = 0", see below.

> + bool enable_tdc = false;

Please remove, see below.

>
> brp = bt->brp - 1;
> sjw = bt->sjw - 1;
> @@ -1006,9 +1013,41 @@ static int m_can_set_bittiming(struct net_device *dev)
> sjw = dbt->sjw - 1;
> tseg1 = dbt->prop_seg + dbt->phase_seg1 - 1;
> tseg2 = dbt->phase_seg2 - 1;
> +
> + /* TDC is only needed for bitrates beyond 2.5 MBit/s.
> + * This is mentioned in the "Bit Time Requirements for CAN FD"
> + * paper presented at the International CAN Conference 2013
> + */
> + if (dbt->bitrate > 2500000) {
> + /* Use the same value of secondary sampling point
> + * as the data sampling point
> + */
> + ssp = dbt->sample_point;
> +
> + /* Equation based on Bosch's M_CAN User Manual's
> + * Transmitter Delay Compensation Section
> + */
> + tdco = (priv->can.clock.freq / 1000) *
> + ssp / dbt->bitrate;
> +
> + /* Max valid TDCO value is 127 */
> + if (tdco > 127) {
> + netdev_warn(dev, "TDCO value of %u is beyond maximum limit. Disabling Transmitter Delay Compensation mode\n",

"maximum limit"? Either "maximum" or "limit" should be enough. If the
value is above 127, does it make sense to disable the tdco completely?

> + tdco);
> + } else {
> + enable_tdc = true;

Why not set "reg_btp |= DBTP_TDC;" here directly?

> + m_can_write(priv, M_CAN_TDCR,
> + tdco << TDCR_TDCO_SHIFT);
> + }
> + }
> +
> reg_btp = (brp << DBTP_DBRP_SHIFT) | (sjw << DBTP_DSJW_SHIFT) |
> (tseg1 << DBTP_DTSEG1_SHIFT) |
> (tseg2 << DBTP_DTSEG2_SHIFT);

Adjust this to "reg_btp |=".

> +
> + if (enable_tdc)
> + reg_btp |= DBTP_TDC;

Please remove.

> +
> m_can_write(priv, M_CAN_DBTP, reg_btp);
> }
>
>

Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Industrial Linux Solutions | Phone: +49-231-2826-924 |
Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2018-01-02 14:35    [W:0.123 / U:1.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site