lkml.org 
[lkml]   [2017]   [Sep]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 05/10] dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
On Fri, Sep 08, 2017 at 09:25:38AM +0200, Maxime Ripard wrote:
> On Fri, Sep 08, 2017 at 09:11:51AM +0200, Corentin Labbe wrote:
> > This patch add documentation about the MDIO switch used on sun8i-h3-emac
> > for integrated PHY.
> >
> > Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
> > ---
> > .../devicetree/bindings/net/dwmac-sun8i.txt | 127 +++++++++++++++++++--
> > 1 file changed, 120 insertions(+), 7 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> > index 725f3b187886..3fa0e54825ea 100644
> > --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> > +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> > @@ -39,7 +39,7 @@ Optional properties for the following compatibles:
> > - allwinner,leds-active-low: EPHY LEDs are active low
> >
> > Required child node of emac:
> > -- mdio bus node: should be named mdio
> > +- mdio bus node: should be labelled mdio
>
> labels do not end up in the final DT (while the names do) so why are
> you making this change?
>

I misunderstood label/name.
Anyway, this contrainst should leave due to "snps,dwmac-mdio MDIOs are automatically registered"

> >
> > Required properties of the mdio node:
> > - #address-cells: shall be 1
> > @@ -48,14 +48,28 @@ Required properties of the mdio node:
> > The device node referenced by "phy" or "phy-handle" should be a child node
> > of the mdio node. See phy.txt for the generic PHY bindings.
> >
> > -Required properties of the phy node with the following compatibles:
> > +The following compatibles require an mdio-mux node called "mdio-mux":
> > + - "allwinner,sun8i-h3-emac"
> > + - "allwinner,sun8i-v3s-emac":
> > +Required properties for the mdio-mux node:
> > + - compatible = "mdio-mux"
> > + - one child mdio for the integrated mdio
> > + - one child mdio for the external mdio if present (V3s have none)
> > +Required properties for the mdio-mux children node:
> > + - reg: 0 for internal MDIO bus, 1 for external MDIO bus
> > +
> > +The following compatibles require a PHY node representing the integrated
> > +PHY, under the integrated MDIO bus node if an mdio-mux node is used:
> > - "allwinner,sun8i-h3-emac",
> > - "allwinner,sun8i-v3s-emac":
> > +
> > +Required properties of the integrated phy node:
> > - clocks: a phandle to the reference clock for the EPHY
> > - resets: a phandle to the reset control for the EPHY
> > +- phy-is-integrated
> > +- Should be a child of the integrated mdio
>
> I'm not sure what you mean by that, you ask that it should (so not
> required?) be a child of the integrated mdio...
>

I will change words to "must"

> >
> > -Example:
> > -
> > +Example with integrated PHY:
> > emac: ethernet@1c0b000 {
> > compatible = "allwinner,sun8i-h3-emac";
> > syscon = <&syscon>;
> > @@ -72,13 +86,112 @@ emac: ethernet@1c0b000 {
> > phy-handle = <&int_mii_phy>;
> > phy-mode = "mii";
> > allwinner,leds-active-low;
> > +
> > + mdio0: mdio {
>
> (You don't label it mdio here, unlike what was asked before)
>
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "snps,dwmac-mdio";
> > + };
>
> I think Rob wanted that node gone?
>

MDIO mux does not work without a parent MDIO, either gived by "parent-bus" or directly via mdio_mux_init() (like it is the case in dwmac-sun8i)

> > + mdio-mux {
> > + compatible = "mdio-mux";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + int_mdio: mdio@1 {
> > + reg = <0>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + int_mii_phy: ethernet-phy@1 {
> > + reg = <1>;
> > + clocks = <&ccu CLK_BUS_EPHY>;
> > + resets = <&ccu RST_BUS_EPHY>;
> > + phy-is-integrated
> > + };
> > + };
>
> ... And in your example it's a child of the mdio mux?
>

So I confirm, integrated PHY must be a child of integrated MDIO (that must be a child of mdio-mux).
The example is good.

> > + ext_mdio: mdio@0 {
> > + reg = <1>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + };
> > + };
> > +};
> > +
> > +Example with external PHY:
> > +emac: ethernet@1c0b000 {
> > + compatible = "allwinner,sun8i-h3-emac";
> > + syscon = <&syscon>;
> > + reg = <0x01c0b000 0x104>;
> > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "macirq";
> > + resets = <&ccu RST_BUS_EMAC>;
> > + reset-names = "stmmaceth";
> > + clocks = <&ccu CLK_BUS_EMAC>;
> > + clock-names = "stmmaceth";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + phy-handle = <&ext_rgmii_phy>;
> > + phy-mode = "rgmii";
> > + allwinner,leds-active-low;
> > +
> > + mdio0: mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "snps,dwmac-mdio";
> > + };
> > +
> > + mdio-mux {
> > + compatible = "mdio-mux";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + int_mdio: mdio@1 {
> > + reg = <0>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + int_mii_phy: ethernet-phy@1 {
> > + reg = <1>;
> > + clocks = <&ccu CLK_BUS_EPHY>;
> > + resets = <&ccu RST_BUS_EPHY>;
> > + phy-is-integrated
> > + };
> > + };
> > + ext_mdio: mdio@0 {
> > + reg = <1>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + ext_rgmii_phy: ethernet-phy@1 {
> > + reg = <1>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +Example with SoC without integrated PHY
> > +
> > +emac: ethernet@1c0b000 {
> > + compatible = "allwinner,sun8i-a83t-emac";
> > + syscon = <&syscon>;
> > + reg = <0x01c0b000 0x104>;
> > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "macirq";
> > + resets = <&ccu RST_BUS_EMAC>;
> > + reset-names = "stmmaceth";
> > + clocks = <&ccu CLK_BUS_EMAC>;
> > + clock-names = "stmmaceth";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + phy-handle = <&ext_rgmii_phy>;
> > + phy-mode = "rgmii";
> > +
> > mdio: mdio {
> > + compatible = "snps,dwmac-mdio";
> > #address-cells = <1>;
> > #size-cells = <0>;
> > - int_mii_phy: ethernet-phy@1 {
> > + ext_rgmii_phy: ethernet-phy@1 {
> > reg = <1>;
> > - clocks = <&ccu CLK_BUS_EPHY>;
> > - resets = <&ccu RST_BUS_EPHY>;
> > };
> > };
> > };
> > --
> > 2.13.5
> >
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com

Thanks for the review, I will fix all reported problem in next version.

Regards
Corentin Labbe

\
 
 \ /
  Last update: 2017-09-08 09:44    [W:0.088 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site