lkml.org 
[lkml]   [2017]   [Sep]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 05/10] dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
On Fri, Sep 08, 2017 at 09:11:51AM +0200, Corentin Labbe wrote:
> This patch add documentation about the MDIO switch used on sun8i-h3-emac
> for integrated PHY.
>
> Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
> ---
> .../devicetree/bindings/net/dwmac-sun8i.txt | 127 +++++++++++++++++++--
> 1 file changed, 120 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> index 725f3b187886..3fa0e54825ea 100644
> --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> @@ -39,7 +39,7 @@ Optional properties for the following compatibles:
> - allwinner,leds-active-low: EPHY LEDs are active low
>
> Required child node of emac:
> -- mdio bus node: should be named mdio
> +- mdio bus node: should be labelled mdio

labels do not end up in the final DT (while the names do) so why are
you making this change?

>
> Required properties of the mdio node:
> - #address-cells: shall be 1
> @@ -48,14 +48,28 @@ Required properties of the mdio node:
> The device node referenced by "phy" or "phy-handle" should be a child node
> of the mdio node. See phy.txt for the generic PHY bindings.
>
> -Required properties of the phy node with the following compatibles:
> +The following compatibles require an mdio-mux node called "mdio-mux":
> + - "allwinner,sun8i-h3-emac"
> + - "allwinner,sun8i-v3s-emac":
> +Required properties for the mdio-mux node:
> + - compatible = "mdio-mux"
> + - one child mdio for the integrated mdio
> + - one child mdio for the external mdio if present (V3s have none)
> +Required properties for the mdio-mux children node:
> + - reg: 0 for internal MDIO bus, 1 for external MDIO bus
> +
> +The following compatibles require a PHY node representing the integrated
> +PHY, under the integrated MDIO bus node if an mdio-mux node is used:
> - "allwinner,sun8i-h3-emac",
> - "allwinner,sun8i-v3s-emac":
> +
> +Required properties of the integrated phy node:
> - clocks: a phandle to the reference clock for the EPHY
> - resets: a phandle to the reset control for the EPHY
> +- phy-is-integrated
> +- Should be a child of the integrated mdio

I'm not sure what you mean by that, you ask that it should (so not
required?) be a child of the integrated mdio...

>
> -Example:
> -
> +Example with integrated PHY:
> emac: ethernet@1c0b000 {
> compatible = "allwinner,sun8i-h3-emac";
> syscon = <&syscon>;
> @@ -72,13 +86,112 @@ emac: ethernet@1c0b000 {
> phy-handle = <&int_mii_phy>;
> phy-mode = "mii";
> allwinner,leds-active-low;
> +
> + mdio0: mdio {

(You don't label it mdio here, unlike what was asked before)

> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + };

I think Rob wanted that node gone?

> + mdio-mux {
> + compatible = "mdio-mux";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + int_mdio: mdio@1 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + int_mii_phy: ethernet-phy@1 {
> + reg = <1>;
> + clocks = <&ccu CLK_BUS_EPHY>;
> + resets = <&ccu RST_BUS_EPHY>;
> + phy-is-integrated
> + };
> + };

... And in your example it's a child of the mdio mux?

> + ext_mdio: mdio@0 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +};
> +
> +Example with external PHY:
> +emac: ethernet@1c0b000 {
> + compatible = "allwinner,sun8i-h3-emac";
> + syscon = <&syscon>;
> + reg = <0x01c0b000 0x104>;
> + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "macirq";
> + resets = <&ccu RST_BUS_EMAC>;
> + reset-names = "stmmaceth";
> + clocks = <&ccu CLK_BUS_EMAC>;
> + clock-names = "stmmaceth";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy-handle = <&ext_rgmii_phy>;
> + phy-mode = "rgmii";
> + allwinner,leds-active-low;
> +
> + mdio0: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + };
> +
> + mdio-mux {
> + compatible = "mdio-mux";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + int_mdio: mdio@1 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + int_mii_phy: ethernet-phy@1 {
> + reg = <1>;
> + clocks = <&ccu CLK_BUS_EPHY>;
> + resets = <&ccu RST_BUS_EPHY>;
> + phy-is-integrated
> + };
> + };
> + ext_mdio: mdio@0 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ext_rgmii_phy: ethernet-phy@1 {
> + reg = <1>;
> + };
> + };
> + };
> +};
> +
> +Example with SoC without integrated PHY
> +
> +emac: ethernet@1c0b000 {
> + compatible = "allwinner,sun8i-a83t-emac";
> + syscon = <&syscon>;
> + reg = <0x01c0b000 0x104>;
> + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "macirq";
> + resets = <&ccu RST_BUS_EMAC>;
> + reset-names = "stmmaceth";
> + clocks = <&ccu CLK_BUS_EMAC>;
> + clock-names = "stmmaceth";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy-handle = <&ext_rgmii_phy>;
> + phy-mode = "rgmii";
> +
> mdio: mdio {
> + compatible = "snps,dwmac-mdio";
> #address-cells = <1>;
> #size-cells = <0>;
> - int_mii_phy: ethernet-phy@1 {
> + ext_rgmii_phy: ethernet-phy@1 {
> reg = <1>;
> - clocks = <&ccu CLK_BUS_EPHY>;
> - resets = <&ccu RST_BUS_EPHY>;
> };
> };
> };
> --
> 2.13.5
>

--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2017-09-08 09:26    [W:0.128 / U:7.364 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site