lkml.org 
[lkml]   [2017]   [Sep]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/1] usb:xhci: update condition to select bus->sysdev from parent device
From
Date
On 24.08.2017 05:53, Thang Q. Nguyen wrote:
> On Sat, Aug 19, 2017 at 10:43 AM, Thang Q. Nguyen <tqnguyen@apm.com> wrote:
>> From: "Thang Q. Nguyen" <tqnguyen@apm.com>
>>
>> For commit 4c39d4b949d3 ("usb: xhci: use bus->sysdev for DMA
>> configuration"), sysdev points to devices known to the system firmware
>> or hardware for DMA parameters.
>> However, the parent of the system firmware/hardware device checking
>> logic does not work in ACPI boot mode. This patch updates the formulation
>> to check this case in both DT and ACPI.
>>
>> Signed-off-by: Tung Nguyen <tunguyen@apm.com>
>> Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
>> ---
>> Change since v1:
>> - Update codes to work with kernel 4.13-rc5
>> ---
>> drivers/usb/host/xhci-plat.c | 5 ++++-
>> 1 file changed, 4 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
>> index c04144b..1bb9729 100644
>> --- a/drivers/usb/host/xhci-plat.c
>> +++ b/drivers/usb/host/xhci-plat.c
>> @@ -187,7 +187,10 @@ static int xhci_plat_probe(struct platform_device *pdev)
>> * 3. xhci_plat is grandchild of a pci device (dwc3-pci)
>> */
>> sysdev = &pdev->dev;
>> - if (sysdev->parent && !sysdev->of_node && sysdev->parent->of_node)
>> + if (sysdev->parent && !is_of_node(sysdev->fwnode) &&
>> + !is_acpi_device_node(sysdev->fwnode) &&
>> + (is_of_node(sysdev->parent->fwnode) ||
>> + is_acpi_device_node(sysdev->parent->fwnode)))
>> sysdev = sysdev->parent;
>> #ifdef CONFIG_PCI
>> else if (sysdev->parent && sysdev->parent->parent &&
>> --
>> 1.8.3.1
>>
> Is there any comment about the patch?
> With current kernel (4.13.0-rc6), booting the Linux using ACPI boot,
> kernel is crashed right after probing the USB DWC3 driver with the
> following messages:

That should work, but the if statements are getting quite elaborate.
How about replacing it all with:

- sysdev = &pdev->dev;
- if (sysdev->parent && !sysdev->of_node && sysdev->parent->of_node)
- sysdev = sysdev->parent;
-#ifdef CONFIG_PCI
- else if (sysdev->parent && sysdev->parent->parent &&
- sysdev->parent->parent->bus == &pci_bus_type)
- sysdev = sysdev->parent->parent;
-#endif
+
+ for (sysdev = &pdev->dev; sysdev; sysdev = sysdev->parent) {
+ if (is_of_node(sysdev->fwnode) ||
+ is_acpi_device_node(sysdev->fwnode))
+ break;
+ #ifdef CONFIG_PCI
+ else if (sysdev->bus == &pci_bus_type)
+ break;
+ #endif
+ }
+
+ if (!sysdev)
+ sysdev = &pdev->dev

Does that work for you?

-Mathias

\
 
 \ /
  Last update: 2017-09-05 13:10    [W:0.063 / U:0.196 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site