lkml.org 
[lkml]   [2017]   [Sep]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 3/3] platform/x86: intel_cht_int33fe: Update fusb302 type string, add properties
Date
The fusb302 driver as merged in staging uses "typec_fusb302" as i2c-id
rather then just "fusb302" and needs us to set a number of device-
properties, adjust the intel_cht_int33fe driver accordingly.

One of the properties set is max-snk-mv which makes the fusb302 driver
negotiate up to 12V charging voltage, which is a bad idea on boards
which are not setup to handle this, so this commit also adds 2 extra
sanity checks to make sure that the expected Whiskey Cove PMIC +
TI bq24292i charger combo, which can handle 12V, is present.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---
Changes in v2:
-Set board_info.dev_name
-Adjust for changes in other patches in this patch-set

Changes in v5:
-Improve Kconfig help text
---
drivers/platform/x86/Kconfig | 6 ++++-
drivers/platform/x86/intel_cht_int33fe.c | 44 +++++++++++++++++++++++++++++++-
2 files changed, 48 insertions(+), 2 deletions(-)

diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index 80b87954f6dd..312d2472b8b3 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -793,7 +793,7 @@ config ACPI_CMPC

config INTEL_CHT_INT33FE
tristate "Intel Cherry Trail ACPI INT33FE Driver"
- depends on X86 && ACPI && I2C
+ depends on X86 && ACPI && I2C && REGULATOR
---help---
This driver add support for the INT33FE ACPI device found on
some Intel Cherry Trail devices.
@@ -804,6 +804,10 @@ config INTEL_CHT_INT33FE
This driver instantiates i2c-clients for these, so that standard
i2c drivers for these chips can bind to the them.

+ If you enable this driver it is advised to also select
+ CONFIG_TYPEC_FUSB302=m (under "Staging drivers"),
+ CONFIG_CHARGER_BQ24190=m and CONFIG_BATTERY_MAX17042=m.
+
config INTEL_INT0002_VGPIO
tristate "Intel ACPI INT0002 Virtual GPIO driver"
depends on GPIOLIB && ACPI
diff --git a/drivers/platform/x86/intel_cht_int33fe.c b/drivers/platform/x86/intel_cht_int33fe.c
index a9cbc4b8ca63..b2925d996613 100644
--- a/drivers/platform/x86/intel_cht_int33fe.c
+++ b/drivers/platform/x86/intel_cht_int33fe.c
@@ -24,6 +24,7 @@
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/module.h>
+#include <linux/regulator/consumer.h>
#include <linux/slab.h>

#define EXPECTED_PTYPE 4
@@ -77,12 +78,21 @@ static const struct property_entry max17047_props[] = {
{ }
};

+static const struct property_entry fusb302_props[] = {
+ PROPERTY_ENTRY_STRING("fcs,extcon-name", "cht_wcove_pwrsrc"),
+ PROPERTY_ENTRY_U32("fcs,max-sink-microvolt", 12000000),
+ PROPERTY_ENTRY_U32("fcs,max-sink-microamp", 3000000),
+ PROPERTY_ENTRY_U32("fcs,max-sink-microwatt", 36000000),
+ { }
+};
+
static int cht_int33fe_probe(struct i2c_client *client)
{
struct device *dev = &client->dev;
struct i2c_board_info board_info;
struct cht_int33fe_data *data;
struct i2c_client *max17047;
+ struct regulator *regulator;
unsigned long long ptyp;
acpi_status status;
int ret, fusb302_irq;
@@ -100,6 +110,34 @@ static int cht_int33fe_probe(struct i2c_client *client)
if (ptyp != EXPECTED_PTYPE)
return -ENODEV;

+ /* Check presence of INT34D3 (hardware-rev 3) expected for ptype == 4 */
+ if (!acpi_dev_present("INT34D3", "1", 3)) {
+ dev_err(dev, "Error PTYPE == %d, but no INT34D3 device\n",
+ EXPECTED_PTYPE);
+ return -ENODEV;
+ }
+
+ /*
+ * We expect the WC PMIC to be paired with a TI bq24292i charger-IC.
+ * We check for the bq24292i vbus regulator here, this has 2 purposes:
+ * 1) The bq24292i allows charging with up to 12V, setting the fusb302's
+ * max-snk voltage to 12V with another charger-IC is not good.
+ * 2) For the fusb302 driver to get the bq24292i vbus regulator, the
+ * regulator-map, which is part of the bq24292i regulator_init_data,
+ * must be registered before the fusb302 is instantiated, otherwise
+ * it will end up with a dummy-regulator.
+ * Note "cht_wc_usb_typec_vbus" comes from the regulator_init_data
+ * which is defined in i2c-cht-wc.c from where the bq24292i i2c-client
+ * gets instantiated. We use regulator_get_optional here so that we
+ * don't end up getting a dummy-regulator ourselves.
+ */
+ regulator = regulator_get_optional(dev, "cht_wc_usb_typec_vbus");
+ if (IS_ERR(regulator)) {
+ ret = PTR_ERR(regulator);
+ return (ret == -ENODEV) ? -EPROBE_DEFER : ret;
+ }
+ regulator_put(regulator);
+
/* The FUSB302 uses the irq at index 1 and is the only irq user */
fusb302_irq = acpi_dev_gpio_irq_get(ACPI_COMPANION(dev), 1);
if (fusb302_irq < 0) {
@@ -126,6 +164,7 @@ static int cht_int33fe_probe(struct i2c_client *client)
} else {
memset(&board_info, 0, sizeof(board_info));
strlcpy(board_info.type, "max17047", I2C_NAME_SIZE);
+ board_info.dev_name = "max17047";
board_info.properties = max17047_props;
data->max17047 = i2c_acpi_new_device(dev, 1, &board_info);
if (!data->max17047)
@@ -133,7 +172,9 @@ static int cht_int33fe_probe(struct i2c_client *client)
}

memset(&board_info, 0, sizeof(board_info));
- strlcpy(board_info.type, "fusb302", I2C_NAME_SIZE);
+ strlcpy(board_info.type, "typec_fusb302", I2C_NAME_SIZE);
+ board_info.dev_name = "fusb302";
+ board_info.properties = fusb302_props;
board_info.irq = fusb302_irq;

data->fusb302 = i2c_acpi_new_device(dev, 2, &board_info);
@@ -141,6 +182,7 @@ static int cht_int33fe_probe(struct i2c_client *client)
goto out_unregister_max17047;

memset(&board_info, 0, sizeof(board_info));
+ board_info.dev_name = "pi3usb30532";
strlcpy(board_info.type, "pi3usb30532", I2C_NAME_SIZE);

data->pi3usb30532 = i2c_acpi_new_device(dev, 3, &board_info);
--
2.13.4
\
 
 \ /
  Last update: 2017-09-04 15:48    [W:0.069 / U:5.112 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site