lkml.org 
[lkml]   [2017]   [Sep]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] PCI: Fix legacy IRQ assignment execution stage
On Thu, Sep 28, 2017 at 05:37:19PM -0500, Bjorn Helgaas wrote:
> On Thu, Sep 28, 2017 at 12:37:07PM +0100, Lorenzo Pieralisi wrote:
> > Through struct pci_host_bridge->{map/swizzle}_irq() hooks is now
> > possible to define IRQ mapping functions on a per PCI host bridge basis.
> >
> > Actual IRQ allocation is carried out by the pci_assign_irq() function in
> > pci_device_probe() - to make sure a device is assigned an IRQ only if it
> > is probed (ie match a driver); it retrieves a struct pci_host_bridge*
> > for a given PCI device and through {map/swizzle}_irq() hooks it carries
> > out the PCI IRQ allocation.
> >
> > As it turned out, some legacy drivers (eg IDE layer) require that a
> > device allocates IRQ as soon as it is added so that its actual IRQ
> > settings are available early in the boot process. With current code
> > calling pci_assign_irq() in pci_device_probe() IDE IRQ probing fails
> > for some drivers:
>
> I think the patch is fine, but I don't understand the changelog. I
> want to know specifically what the dependency on dev->irq is. "Early
> in the boot process" is pretty vague.
>
> I *thought* we were doing something like this:
>
> pci_device_probe(dev1)
> pci_assign_irq(dev1)
> ...
> ide_pci_init_two(dev1, dev2, ...)
> do_ide_setup_pci_device(dev1)
> pciirq = dev1->irq # this one is fine
> do_ide_setup_pci_device(dev2)
> pciirq = dev2->irq # not fine
>
> where the problem is that we haven't called pci_assign_irq(dev2), so
> dev2->irq hasn't been set.
>
> But that doesn't match the data because we should be coming through
> cmd64x_init_one(), which calls ide_pci_init_one(), so we shouldn't
> have a dev2 in this path.

I *think* I understand what's going on here, the key is:

ide_scan_pcibus()

and CONFIG_IDEPCI_PCIBUS_ORDER

I still have to replicate it but I suspect that
do_ide_setup_pci_device() for dev1 finds an unallocated IRQ (ie dev->irq
== 0) because the probing did NOT happen via pci_device_probe(), ie
pci_device_probe() was not called for the dev1, the cmd64x probe
routine is called straight from ide_scan_pcidev().

I am struggling to understand the logic behind:

ide_pci_register_driver() and ide_scan_pcibus()

and the sequence wrt PCI bus probing but I think that's the problem
and that's why moving pci_assign_irq() to pci_device_add() will
sort this out, adding pci_assign_irq() in ide_scan_pcidev() will
solve the problem too (patch below).

Needless to say, ide_scan_pcibus() relies on pre_init global variable
to make sure ide_pci_register_driver() chooses the "right" way of
registering a driver, see:

__ide_pci_register_driver()

Patch here to verify my assumption in case Guenter has a chance to
run it if I do not beat him to it:

-- >8 --
diff --git a/drivers/ide/ide-scan-pci.c b/drivers/ide/ide-scan-pci.c
index 86aa88a..86b570a 100644
--- a/drivers/ide/ide-scan-pci.c
+++ b/drivers/ide/ide-scan-pci.c
@@ -56,6 +56,8 @@ static int __init ide_scan_pcidev(struct pci_dev *dev)
{
struct list_head *l;
struct pci_driver *d;
+ int ret;
+

list_for_each(l, &ide_pci_drivers) {
d = list_entry(l, struct pci_driver, node);
@@ -63,10 +65,14 @@ static int __init ide_scan_pcidev(struct pci_dev *dev)
const struct pci_device_id *id =
pci_match_id(d->id_table, dev);

- if (id != NULL && d->probe(dev, id) >= 0) {
- dev->driver = d;
- pci_dev_get(dev);
- return 1;
+ if (id != NULL) {
+ pci_assign_irq(dev);
+ ret = d->probe(dev, id);
+ if (ret >= 0) {
+ dev->driver = d;
+ pci_dev_get(dev);
+ return 1;
+ }
}
}
}
\
 
 \ /
  Last update: 2017-09-29 18:00    [W:0.081 / U:0.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site