lkml.org 
[lkml]   [2017]   [Sep]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 6/7] ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
Date
This patch adds device nodes for all the regulators of the AXP813 PMIC.
References to the 3.3V dummy regulator are replaced, and it is disabled.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 134 ++++++++++++++++++++++++++-
1 file changed, 132 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index 2bafd7e99ef7..c7dae2e5a668 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -71,7 +71,7 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <&reg_vcc3v3>;
+ vmmc-supply = <&reg_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
@@ -81,7 +81,7 @@
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_emmc_pins>;
- vmmc-supply = <&reg_vcc3v3>;
+ vmmc-supply = <&reg_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
@@ -96,6 +96,10 @@
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <&reg_dcdc1>;
+ fldoin-supply = <&reg_dcdc5>;
+ swin-supply = <&reg_dcdc1>;
+ x-powers,drive-vbus-en;
};

ac100: codec@e89 {
@@ -123,6 +127,128 @@
};
};

+#include "axp81x.dtsi"
+
+&reg_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18-csi2-dsi-efuse-hdmi";
+};
+
+&reg_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vdd-drampll-vcc18-pll-adc-cpvdd-ldoin";
+};
+
+&reg_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pl-avcc";
+};
+
+&reg_dcdc1 {
+ /* schematics says 3.1V but FEX file says 3.3V */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+};
+
+&reg_dcdc4 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-sys-vdd09-usb0-hdmi";
+};
+
+&reg_dldo1 {
+ /*
+ * This powers both the WiFi/BT module's main power, I/O supply,
+ * and external pull-ups on all the data lines. It should be set
+ * to the same voltage as the I/O supply (DCDC1 in this case) to
+ * avoid any leakage or mismatch.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&reg_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pd";
+};
+
+&reg_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&reg_fldo1 {
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd12-hsic";
+};
+
+&reg_fldo2 {
+ /*
+ * Despite the embedded CPUs core not being used in any way,
+ * this must remain on or the system will hang.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+ regulator-name = "vcc-rtc-vdd1v8-io-vdd18-lvds";
+};
+
+&reg_sw {
+ /*
+ * The PHY requires 20ms after all voltages
+ * are applied until core logic is ready and
+ * 30ms after the reset pin is de-asserted.
+ * Set a 100ms delay to account for PMIC
+ * ramp time and board traces.
+ */
+ regulator-enable-ramp-delay = <100000>;
+ regulator-name = "vcc-gmac";
+};
+
&reg_usb1_vbus {
gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
status = "okay";
@@ -132,6 +258,10 @@
status = "disabled";
};

+&reg_vcc3v3 {
+ status = "disabled";
+};
+
&reg_vcc5v0 {
status = "disabled";
};
--
2.14.2
\
 
 \ /
  Last update: 2017-09-29 05:26    [W:0.099 / U:3.860 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site