lkml.org 
[lkml]   [2017]   [Aug]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 1/2] arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2
From
Date


On 08/04/2017 12:14 PM, Sean Wang wrote:
> On Fri, 2017-08-04 at 11:59 +0800, sean.wang@mediatek.com wrote:
>> From: Sean Wang <sean.wang@mediatek.com>
>>
>> The bananapi-r2 board has an SD-card controller and built-in
>> EMMC storage so enables those devices in the devicetree. Also
>> cleanup nodes in alphabetical order in the patch.
>>
>
> Hi, Matthias
>
> could your help remove those words "Also cleanup nodes in alphabetical
> order in the patch." when merging, i was forgetting to do it.
>
> or prefer wanting me to resend it again?

Yes I can do that. No need to resend.

Regards,
Matthias

>
> Sean
>
>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
>> Signed-off-by: Sean Wang <sean.wang@mediatek.com>
>> ---
>> arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 37 +++++++++++++++++++++++++++
>> 1 file changed, 37 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> index 9f3e6dd..444ed93 100644
>> --- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> +++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> @@ -179,6 +179,32 @@
>> status = "okay";
>> };
>>
>> +&mmc0 {
>> + pinctrl-names = "default", "state_uhs";
>> + pinctrl-0 = <&mmc0_pins_default>;
>> + pinctrl-1 = <&mmc0_pins_uhs>;
>> + status = "okay";
>> + bus-width = <8>;
>> + max-frequency = <50000000>;
>> + cap-mmc-highspeed;
>> + vmmc-supply = <&mt6323_vemc3v3_reg>;
>> + vqmmc-supply = <&mt6323_vio18_reg>;
>> + non-removable;
>> +};
>> +
>> +&mmc1 {
>> + pinctrl-names = "default", "state_uhs";
>> + pinctrl-0 = <&mmc1_pins_default>;
>> + pinctrl-1 = <&mmc1_pins_uhs>;
>> + status = "okay";
>> + bus-width = <4>;
>> + max-frequency = <50000000>;
>> + cap-sd-highspeed;
>> + cd-gpios = <&pio 261 0>;
>> + vmmc-supply = <&mt6323_vmch_reg>;
>> + vqmmc-supply = <&mt6323_vio18_reg>;
>> +};
>> +
>> &pio {
>> cir_pins_a:cir@0 {
>> pins_cir {
>> @@ -314,6 +340,17 @@
>> bias-pull-down;
>> drive-strength = <MTK_DRIVE_4mA>;
>> };
>> +
>> + pins_wp {
>> + pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>;
>> + input-enable;
>> + bias-pull-up;
>> + };
>> +
>> + pins_insert {
>> + pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>;
>> + bias-pull-up;
>> + };
>> };
>>
>> mmc1_pins_uhs: mmc1 {
>
>

\
 
 \ /
  Last update: 2017-08-04 14:20    [W:0.147 / U:0.316 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site