lkml.org 
[lkml]   [2017]   [Aug]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2 00/16] mmc: meson-gx: driver fixups and upgrades
Date
Ulf Hansson <ulf.hansson@linaro.org> writes:

> On 22 August 2017 at 13:46, Jerome Brunet <jbrunet@baylibre.com> wrote:
>> On Tue, 2017-08-22 at 13:15 +0200, Ulf Hansson wrote:
>>> On 21 August 2017 at 18:02, Jerome Brunet <jbrunet@baylibre.com> wrote:
>>> > The patchset features several bugfixes, rework and upgrade for the
>>> > meson-gx MMC driver.
>>> >
>>> > The main goal is to improve readability and enable new high speed
>>> > modes, such as eMMC DDR52 and sdcard UHS modes up to SDR50 (100Mhz)
>>> >
>>> > SDR104 is not working with a few cards on the p200 and the
>>> > libretech-cc. I suspect that 200Mhz might be a bit too fast for the PCB
>>> > of these boards, adding noise to the signal and eventually breaking
>>> > the communication with some cards. The same cards are working well on a
>>> > laptop or the nanopi-k2 at 200Mhz.
>>> >
>>> > This series has been tested on gxbb-p200, gxbb-nanopi-k2 and
>>> > gxl-s905x-libretech-cc
>>> >
>>> > Changes since v1 [0]:
>>> > * Reorder patches to have fixes first, then rework and finally
>>> > enhancements.
>>> > * Use CCF to manage clock phases
>>> >
>>> > [0]: https://lkml.kernel.org/r/20170804174353.16486-1-jbrunet@baylibre.com
>>> >
>>> > Jerome Brunet (16):
>>> > mmc: meson-gx: fix mux mask definition
>>> > mmc: meson-gx: remove CLK_DIVIDER_ALLOW_ZERO clock flag
>>> > mmc: meson-gx: clean up some constants
>>> > mmc: meson-gx: use _irqsave variant of spinlock
>>> > mmc: meson-gx: cfg init overwrite values
>>> > mmc: meson-gx: rework set_ios function
>>> > mmc: meson-gx: rework clk_set function
>>> > mmc: meson-gx: rework clock init function
>>> > mmc: meson-gx: fix dual data rate mode frequencies
>>> > mmc: meson-gx: work around clk-stop issue
>>> > mmc: meson-gx: simplify interrupt handler
>>> > mmc: meson-gx: implement card_busy callback
>>> > mmc: meson-gx: use CCF to handle the clock phases
>>> > mmc: meson-gx: implement voltage switch callback
>>> > mmc: meson-gx: change default tx phase
>>> > mmc: meson-gx: rework tuning function
>>> >
>>> > drivers/mmc/host/meson-gx-mmc.c | 718 +++++++++++++++++++++++++++--------
>>> > -----
>>> > 1 file changed, 497 insertions(+), 221 deletions(-)
>>> >
>>> > --
>>> > 2.9.5
>>> >
>>>
>>> So far, I decided to pick patch 1 -> 3.
>>
>> Thx Ulf.
>> Do you want me to respin w/o patch 1 -> 4 or shall I wait for further review on
>> the other changes ?
>
> I think you can wait a bit, hopefully some of the earlier authors and
> Kevin can give some input as well.

Most of them already had a Reviewed-by from me, but I just reviewed the
new/updateds one now as well.

Kevin

\
 
 \ /
  Last update: 2017-08-25 02:06    [W:0.065 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site