lkml.org 
[lkml]   [2017]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [v7 wlcore: add missing nvs file name info for wilink8
Date
> >
> > + if (oui_addr == 0xdeadbe && nic_addr == 0xef0000) {
> > + wl1271_warning("Detected unconfigured mac address in
> nvs.\n"
> > + "derive from fuse instead.\n"
> > + "in case of using a wl12xx device, your "
> > + "device performance may not be
> optimized.\n"
> > + "Please use the calibrator tool to configure "
> > + "your device.\n"
> > + "When using a wl18xx device this default nvs
> "
> > + "file can be removed from the file
> system\n");
>
> Usually we do not break multiline messages to make it easier to grep
> for them. Also it feels weird to say "if your device is ..., then
> ...", when we actually know which device it is. I suggest the
> following:
>
> wl1271_warning("Detected unconfigured mac address in nvs, derive from
> fuse instead.\n");
> if (device_is_wl12xx) {
> wl1271_warning("Your device performance is not optimized.\n");
> wl1271_warning("Please use the calibrator tool to configure your
> device.\n");
> } else {
> wl1271_warning("This default nvs file can be removed from the file
> system\n");
> }
OK, will try that out.

>
> > + if (wl->fuse_oui_addr == 0 && wl->fuse_nic_addr == 0) {
> > + wl1271_warning("Fuse mac address is zero. using "
> > + "random mac\n");
>
> This one should also go into one line.

This will still exceed 80 characters. Is this still ok?

>
> > + /* Use TI oui and a random nic */
> > + oui_addr = WLCORE_TI_OUI_ADDRESS;
> > + nic_addr = get_random_int();
> > + } else {
> > + oui_addr = wl->fuse_oui_addr;
> > + /* fuse has the BD_ADDR, the WLAN addresses are
> the next two */
> > + nic_addr = wl->fuse_nic_addr + 1;
> > + }
> > + }
> > +
> > wl12xx_derive_mac_addresses(wl, oui_addr, nic_addr);
> >
> > ret = ieee80211_register_hw(wl->hw);
> > diff --git a/drivers/net/wireless/ti/wlcore/sdio.c
> b/drivers/net/wireless/ti/wlcore/sdio.c
> > index 2fb3871..f8a1fea 100644
> > --- a/drivers/net/wireless/ti/wlcore/sdio.c
> > +++ b/drivers/net/wireless/ti/wlcore/sdio.c
> > @@ -230,6 +230,7 @@ static const struct wilink_family_data wl128x_data =
> {
> > static const struct wilink_family_data wl18xx_data = {
> > .name = "wl18xx",
> > .cfg_name = "ti-connectivity/wl18xx-conf.bin",
> > + .nvs_name = "ti-connectivity/wl1271-nvs.bin",
> > };
> >
> > static const struct of_device_id wlcore_sdio_of_match_table[] = {
> > diff --git a/drivers/net/wireless/ti/wlcore/spi.c
> b/drivers/net/wireless/ti/wlcore/spi.c
> > index fdabb92..62ce54a 100644
> > --- a/drivers/net/wireless/ti/wlcore/spi.c
> > +++ b/drivers/net/wireless/ti/wlcore/spi.c
> > @@ -92,6 +92,7 @@ static const struct wilink_family_data wl128x_data = {
> > static const struct wilink_family_data wl18xx_data = {
> > .name = "wl18xx",
> > .cfg_name = "ti-connectivity/wl18xx-conf.bin",
> > + .nvs_name = "ti-connectivity/wl1271-nvs.bin",
> > };
> >
> > struct wl12xx_spi_glue {
> > diff --git a/drivers/net/wireless/ti/wlcore/wlcore.h
> b/drivers/net/wireless/ti/wlcore/wlcore.h
> > index 1827546..95fbedc 100644
> > --- a/drivers/net/wireless/ti/wlcore/wlcore.h
> > +++ b/drivers/net/wireless/ti/wlcore/wlcore.h
> > @@ -40,6 +40,9 @@
> > /* wl12xx/wl18xx maximum transmission power (in dBm) */
> > #define WLCORE_MAX_TXPWR 25
> >
> > +/* Texas Instruments pre assigned OUI */
> > +#define WLCORE_TI_OUI_ADDRESS 0x080028
> > +
> > /* forward declaration */
> > struct wl1271_tx_hw_descr;
> > enum wl_rx_buf_align;
>
> Otherwise:
>
> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
>
Thank you. Will submit v8 with your comments about the strings.
Just waiting for clarification on the 80 characters question above

Best Regards,
Eyal

\
 
 \ /
  Last update: 2017-08-16 09:18    [W:0.263 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site