lkml.org 
[lkml]   [2017]   [Aug]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] thermal/drivers/hisi: Remove confusing error message
From
Date
On Tue, 2017-08-08 at 21:29 +0800, Leo Yan wrote:
> On Tue, Aug 08, 2017 at 08:48:51PM +0800, Zhang Rui wrote:
>
> [...]
>
> >
> > >
> > > >
> > > > >
> > > > > @@ -352,10 +353,9 @@ static int hisi_thermal_probe(struct
> > > > > platform_device *pdev)
> > > > >   ret = hisi_thermal_register_sensor(pdev,
> > > > > data,
> > > > >      &data-
> > > > > >
> > > > > >
> > > > > > sensors[i], i);
> > > > >   if (ret)
> > > > > - dev_err(&pdev->dev,
> > > > > - "failed to register thermal
> > > > > sensor:
> > > > > %d\n", ret);
> > > > > - else
> > > > > - hisi_thermal_toggle_sensor(&data-
> > > > > >
> > > > > >
> > > > > > sensors[i], true);
> > > > > + continue;
> > > > > +
> > > > > + hisi_thermal_toggle_sensor(&data-
> > > > > >sensors[i],
> > > > > true);
> > > > >   }
> > > > >  
> > > > >   return 0;
> > > > With these removed, is there any other information in dmesg
> > > > that
> > > > suggests this failure?
> > > The problem is there are always failures showed in dmesg. The
> > > init
> > > function is based on the assumption there is HISI_MAX_SENSORS
> > > sensors
> > > which is not true for the hi6220 and that raises at boot time
> > > errors.
> > >
> > > Why HISI_MAX_SENSORS(=4) while there is only one on hi6220 AFAIK?
> > > and
> > > this driver is only used for hi6220 (now).
> > >
> > right, I think we should remove one error log, and then change the
> > HISI_MAX_SENSORS to reflect the reality instead.
> >
> > XinWei and Leo,
> > can you please help check this?
> Sure.
>
> Here I am a bit confusion and I think this is a common question for
> SoC thermal driver.
>
> Hi6220 does has 4 thermal sensors, but we now only use one sensor of
> them (thermal sensor id 2) to bind with thermal zone and other three
> sensors are not bound to any thermal zone. So this is the reason the
> booting reports the failure.
>
> I think changing HISI_MAX_SENSORS value cannot resolve this issue,
> due
> we are using thermal id 2. How about below change? We change to use
> warning for sensors without binding, and remove redundant log.
>
Now we will get three "thermal sensor %d has not bound" messages for
every normal probe, and an extra "failed to register thermal sensor:"
for a real failure probe?

If that's the case, as we are not using the sensors on purpose, why not
keep silence for -ENODEV?

thanks,
rui

> diff --git a/drivers/thermal/hisi_thermal.c
> b/drivers/thermal/hisi_thermal.c
> index 9c3ce34..6d34980 100644
> --- a/drivers/thermal/hisi_thermal.c
> +++ b/drivers/thermal/hisi_thermal.c
> @@ -260,8 +260,6 @@ static int hisi_thermal_register_sensor(struct
> platform_device *pdev,
>         if (IS_ERR(sensor->tzd)) {
>                 ret = PTR_ERR(sensor->tzd);
>                 sensor->tzd = NULL;
> -               dev_err(&pdev->dev, "failed to register sensor id %d:
> %d\n",
> -                       sensor->id, ret);
>                 return ret;
>         }
>  
> @@ -351,7 +349,10 @@ static int hisi_thermal_probe(struct
> platform_device *pdev)
>         for (i = 0; i < HISI_MAX_SENSORS; ++i) {
>                 ret = hisi_thermal_register_sensor(pdev, data,
>                                                    &data->sensors[i],
> i);
> -               if (ret)
> +               if (ret == -ENODEV)
> +                       dev_warn(&pdev->dev,
> +                                "thermal sensor %d has not bound\n",
> i);
> +               else if (ret)
>                         dev_err(&pdev->dev,
>                                 "failed to register thermal sensor:
> %d\n", ret);
>                 else
>
> Thanks,
> Leo Yan

\
 
 \ /
  Last update: 2017-08-11 05:15    [W:0.062 / U:0.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site