lkml.org 
[lkml]   [2017]   [Jul]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [linux-sunxi] [PATCH 02/10] regulator: add support for SY8106A regulator
On Mon, Jul 24, 2017 at 11:18 AM,  <icenowy@aosc.io> wrote:
> 在 2017-07-24 11:03,Chen-Yu Tsai 写道:
>>
>> On Sun, Jul 23, 2017 at 6:27 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
>>>
>>> From: Ondrej Jirman <megous@megous.com>
>>>
>>> SY8106A is an I2C attached single output regulator made by Silergy Corp,
>>> which is used on several Allwinner H3/H5 SBCs to control the power
>>> supply of the ARM cores.
>>>
>>> Add a driver for it.
>>>
>>> Signed-off-by: Ondrej Jirman <megous@megous.com>
>>> [Icenowy: Change commit message]
>>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>>> ---
>>> drivers/regulator/Kconfig | 8 +-
>>> drivers/regulator/Makefile | 2 +-
>>> drivers/regulator/sy8106a-regulator.c | 163
>>> ++++++++++++++++++++++++++++++++++
>>> 3 files changed, 171 insertions(+), 2 deletions(-)
>>> create mode 100644 drivers/regulator/sy8106a-regulator.c
>>>
>>> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
>>> index 99b9362331b5..1efa73e18d07 100644
>>> --- a/drivers/regulator/Kconfig
>>> +++ b/drivers/regulator/Kconfig
>>> @@ -764,6 +764,13 @@ config REGULATOR_STW481X_VMMC
>>> This driver supports the internal VMMC regulator in the STw481x
>>> PMIC chips.
>>>
>>> +config REGULATOR_SY8106A
>>> + tristate "Silergy SY8106A regulator"
>>> + depends on I2C && (OF || COMPILE_TEST)
>>> + select REGMAP_I2C
>>> + help
>>> + This driver supports SY8106A single output regulator.
>>> +
>>> config REGULATOR_TPS51632
>>> tristate "TI TPS51632 Power Regulator"
>>> depends on I2C
>>> @@ -938,4 +945,3 @@ config REGULATOR_WM8994
>>> WM8994 CODEC.
>>>
>>> endif
>>> -
>>> diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
>>> index 95b1e86ae692..f5120252f86a 100644
>>> --- a/drivers/regulator/Makefile
>>> +++ b/drivers/regulator/Makefile
>>> @@ -95,6 +95,7 @@ obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
>>> obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
>>> obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
>>> obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
>>> +obj-$(CONFIG_REGULATOR_SY8106A) += sy8106a-regulator.o
>>> obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
>>> obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
>>> obj-$(CONFIG_REGULATOR_TPS62360) += tps62360-regulator.o
>>> @@ -120,5 +121,4 @@ obj-$(CONFIG_REGULATOR_WM8350) += wm8350-regulator.o
>>> obj-$(CONFIG_REGULATOR_WM8400) += wm8400-regulator.o
>>> obj-$(CONFIG_REGULATOR_WM8994) += wm8994-regulator.o
>>>
>>> -
>>> ccflags-$(CONFIG_REGULATOR_DEBUG) += -DDEBUG
>>> diff --git a/drivers/regulator/sy8106a-regulator.c
>>> b/drivers/regulator/sy8106a-regulator.c
>>> new file mode 100644
>>> index 000000000000..1df889f68b3d
>>> --- /dev/null
>>> +++ b/drivers/regulator/sy8106a-regulator.c
>>> @@ -0,0 +1,163 @@
>>> +/*
>>> + * sy8106a-regulator.c - Regulator device driver for SY8106A
>>> + *
>>> + * Copyright (C) 2016 Ondřej Jirman <megous@megous.com>
>>> + *
>>> + * This program is free software; you can redistribute it and/or
>>> + * modify it under the terms of the GNU Library General Public
>>> + * License as published by the Free Software Foundation; either
>>> + * version 2 of the License, or (at your option) any later version.
>>> + *
>>> + * This program is distributed in the hope that it will be useful,
>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
>>> + * Library General Public License for more details.
>>> + */
>>> +
>>> +#include <linux/err.h>
>>> +#include <linux/i2c.h>
>>> +#include <linux/module.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/regulator/driver.h>
>>> +#include <linux/regulator/of_regulator.h>
>>> +
>>> +#define SY8106A_REG_VOUT1_SEL 0x01
>>> +#define SY8106A_REG_VOUT_COM 0x02
>>> +#define SY8106A_REG_VOUT1_SEL_MASK 0x7f
>>> +#define SY8106A_DISABLE_REG BIT(0)
>>> +#define SY8106A_GO_BIT BIT(7)
>>> +
>>> +struct sy8106a {
>>> + struct regulator_dev *rdev;
>>> + struct regmap *regmap;
>>> +};
>>> +
>>> +static const struct regmap_config sy8106a_regmap_config = {
>>> + .reg_bits = 8,
>>> + .val_bits = 8,
>>> +};
>>> +
>>> +static int sy8106a_set_voltage_sel(struct regulator_dev *rdev, unsigned
>>> int sel)
>>> +{
>>> + /* We use our set_voltage_sel in order to avoid unnecessary I2C
>>> + * chatter, because the regulator_get_voltage_sel_regmap using
>>> + * apply_bit would perform 4 unnecessary transfers instead of
>>> one,
>>> + * increasing the chance of error.
>>> + */
>>> + return regmap_write(rdev->regmap, rdev->desc->vsel_reg,
>>> + sel | SY8106A_GO_BIT);
>>
>>
>> There should also be an explanation of what the "go bit" does.
>> In this case it enables control of the voltage over I2C.
>>
>>> +}
>>> +
>>> +static const struct regulator_ops sy8106a_ops = {
>>> + .is_enabled = regulator_is_enabled_regmap,
>>> + .set_voltage_sel = sy8106a_set_voltage_sel,
>>> + .set_voltage_time_sel = regulator_set_voltage_time_sel,
>>> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
>>> + .list_voltage = regulator_list_voltage_linear,
>>
>>
>> No enable/disable ops?
>>
>>> +};
>>> +
>>> +/* Default limits measured in millivolts and milliamps */
>>> +#define SY8106A_MIN_MV 680
>>> +#define SY8106A_MAX_MV 1950
>>> +#define SY8106A_STEP_MV 10
>>> +
>>> +static const struct regulator_desc sy8106a_reg = {
>>> + .name = "SY8106A",
>>> + .id = 0,
>>> + .ops = &sy8106a_ops,
>>> + .type = REGULATOR_VOLTAGE,
>>> + .n_voltages = ((SY8106A_MAX_MV - SY8106A_MIN_MV) /
>>> SY8106A_STEP_MV) + 1,
>>> + .min_uV = (SY8106A_MIN_MV * 1000),
>>> + .uV_step = (SY8106A_STEP_MV * 1000),
>>> + .vsel_reg = SY8106A_REG_VOUT1_SEL,
>>> + .vsel_mask = SY8106A_REG_VOUT1_SEL_MASK,
>>> + .enable_reg = SY8106A_REG_VOUT_COM,
>>> + .enable_mask = SY8106A_DISABLE_REG,
>>> + .disable_val = SY8106A_DISABLE_REG,
>>> + .enable_is_inverted = 1,
>>
>>
>> As the regulator core helpers currently are, there is no way to disable
>> this regulator. regulator_disable_regmap looks like:
>
>
> By reading the current code, I think removing the disable_val variable will
> just make it work -- when enabling, the enable_reg will be set to disable_val
> (as enable_is_inverted is 1), and disable_val is defaultly 0; when disabling,
> the enable_reg will be set to enable_mask (fallbacked from enable_val, which
> is also the default value 0), and the regulator successfully get disabled.

(Gmail is wrapping the lines :( )

enable_mask is set to SY8106A_DISABLE_REG, which equals disable_val here,
which is not 0. This is correct, as it is the bit mask passed to
regmap_update_bits. So no, it does not work.

It seems quite a lot of drivers depend on this fallback behavior though.

ChenYu

>
>>
>> if (rdev->desc->enable_is_inverted) {
>> val = rdev->desc->enable_val;
>> if (!val)
>> val = rdev->desc->enable_mask;
>> } else {
>> val = rdev->desc->disable_val;
>> }
>>
>> return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
>> rdev->desc->enable_mask, val);
>>
>> Note the fallback to enable_mask if enable_val is not set. The enable
>> helper has a similar structure. This regulator uses an enable value
>> of 0, and disable value of 1, it is impossible to get it right. As
>> it is now, it doesn't really make sense to me.
>>
>> The code was introduced in ca5d1b3524b4 ("regulator: helpers: Modify
>> helpers enabling multi-bit control"). I wonder if it was an unintended
>> consequence of the change? (original author CC-ed)
>>
>>> + .owner = THIS_MODULE,
>>> +};
>>> +
>>> +/*
>>> + * I2C driver interface functions
>>> + */
>>> +static int sy8106a_i2c_probe(struct i2c_client *i2c,
>>> + const struct i2c_device_id *id)
>>> +{
>>> + struct sy8106a *chip;
>>> + struct device *dev = &i2c->dev;
>>> + struct regulator_dev *rdev = NULL;
>>> + struct regulator_config config = { };
>>> + unsigned int selector;
>>> + int error;
>>> +
>>> + chip = devm_kzalloc(&i2c->dev, sizeof(struct sy8106a),
>>> GFP_KERNEL);
>>> + if (!chip)
>>> + return -ENOMEM;
>>> +
>>> + chip->regmap = devm_regmap_init_i2c(i2c, &sy8106a_regmap_config);
>>> + if (IS_ERR(chip->regmap)) {
>>> + error = PTR_ERR(chip->regmap);
>>> + dev_err(&i2c->dev, "Failed to allocate register map:
>>> %d\n",
>>> + error);
>>> + return error;
>>> + }
>>> +
>>> + config.dev = &i2c->dev;
>>> + config.regmap = chip->regmap;
>>> + config.driver_data = chip;
>>> +
>>> + config.of_node = dev->of_node;
>>> + config.init_data = of_get_regulator_init_data(dev, dev->of_node,
>>> + &sy8106a_reg);
>>> +
>>> + if (!config.init_data)
>>> + return -ENOMEM;
>>> +
>>> + /* Probe regulator */
>>> + error = regmap_read(chip->regmap, SY8106A_REG_VOUT1_SEL,
>>> &selector);
>>> + if (error) {
>>> + dev_err(&i2c->dev, "Failed to read voltage at probe time:
>>> %d\n", error);
>>> + return error;
>>> + }
>>> +
>>> + rdev = devm_regulator_register(&i2c->dev, &sy8106a_reg, &config);
>>> + if (IS_ERR(rdev)) {
>>> + error = PTR_ERR(rdev);
>>> + dev_err(&i2c->dev, "Failed to register SY8106A regulator:
>>> %d\n", error);
>>> + return error;
>>> + }
>>> +
>>> + chip->rdev = rdev;
>>> +
>>> + i2c_set_clientdata(i2c, chip);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct of_device_id sy8106a_i2c_of_match[] = {
>>> + { .compatible = "silergy,sy8106a" },
>>> + { },
>>> +};
>>> +MODULE_DEVICE_TABLE(of, sy8106a_i2c_of_match);
>>> +
>>> +static const struct i2c_device_id sy8106a_i2c_id[] = {
>>> + { "sy8106a", 0 },
>>> + { },
>>> +};
>>> +MODULE_DEVICE_TABLE(i2c, sy8106a_i2c_id);
>>> +
>>> +static struct i2c_driver sy8106a_regulator_driver = {
>>> + .driver = {
>>> + .name = "sy8106a",
>>> + .of_match_table = of_match_ptr(sy8106a_i2c_of_match),
>>> + },
>>> + .probe = sy8106a_i2c_probe,
>>> + .id_table = sy8106a_i2c_id,
>>> +};
>>> +
>>> +module_i2c_driver(sy8106a_regulator_driver);
>>> +
>>> +MODULE_AUTHOR("Ondřej Jirman <megous@megous.com>");
>>> +MODULE_DESCRIPTION("Regulator device driver for Silergy SY8106A");
>>> +MODULE_LICENSE("GPL v2");
>>
>>
>> This should be "GPL", to match what the license at the very top says.
>>
>> Regards
>> ChenYu
>>
>>> --
>>> 2.13.0
>>>
>>> --
>>> You received this message because you are subscribed to the Google Groups
>>> "linux-sunxi" group.
>>> To unsubscribe from this group and stop receiving emails from it, send an
>>> email to linux-sunxi+unsubscribe@googlegroups.com.
>>> For more options, visit https://groups.google.com/d/optout.
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
>
> --
> You received this message because you are subscribed to the Google Groups
> "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.

\
 
 \ /
  Last update: 2017-07-24 05:34    [W:0.329 / U:0.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site