lkml.org 
[lkml]   [2017]   [Jul]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [v2 PATCH 2/2] powernv/powerpc: Clear PECE1 in LPCR via stop-api only on Hotplug
On Wed, 19 Jul 2017 13:48:50 +0530
"Gautham R. Shenoy" <ego@linux.vnet.ibm.com> wrote:

> From: "Gautham R. Shenoy" <ego@linux.vnet.ibm.com>
>
> Currently we use the stop-api provided by the firmware to program the
> SLW engine to restore the values of hypervisor resources that get lost
> on deeper idle states (such as winkle). Since the deep states were
> only used for CPU-Hotplug on POWER8 systems, we would program the LPCR
> to have the PECE1 bit since Hotplugged CPUs shouldn't be spuriously
> woken up by decrementer.
>
> On POWER9, some of the deep platform idle states such as stop4 can be
> used in cpuidle as well. In this case, we want the CPU in stop4 to be
> woken up by the decrementer when some timer on the CPU expires.
>
> In this patch, for POWER9, we program the stop-api for LPCR with PECE1
> bit cleared only when we are offlining the CPU.
>
> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
> ---
> arch/powerpc/platforms/powernv/idle.c | 45 ++++++++++++++++++++++++++++++++++-
> arch/powerpc/platforms/powernv/smp.c | 10 --------
> 2 files changed, 44 insertions(+), 11 deletions(-)
>
> diff --git a/arch/powerpc/platforms/powernv/idle.c b/arch/powerpc/platforms/powernv/idle.c
> index 2abee07..a6c69b7 100644
> --- a/arch/powerpc/platforms/powernv/idle.c
> +++ b/arch/powerpc/platforms/powernv/idle.c
> @@ -68,7 +68,7 @@ static int pnv_save_sprs_for_deep_states(void)
> * all cpus at boot. Get these reg values of current cpu and use the
> * same across all cpus.
> */
> - uint64_t lpcr_val = mfspr(SPRN_LPCR) & ~(u64)LPCR_PECE1;
> + uint64_t lpcr_val = mfspr(SPRN_LPCR);
> uint64_t hid0_val = mfspr(SPRN_HID0);
> uint64_t hid1_val = mfspr(SPRN_HID1);
> uint64_t hid4_val = mfspr(SPRN_HID4);
> @@ -85,6 +85,16 @@ static int pnv_save_sprs_for_deep_states(void)
> if (rc != 0)
> return rc;
>
> + /*
> + * On POWER8, the only state that uses SLW engine is
> + * winkle. This is only used for CPU-Hotplug. So we
> + * clear the decrementer bit from LPCR since we
> + * don't want to be woken up on decrementer when in
> + * winkle.
> + */
> + if (!cpu_has_feature(CPU_FTR_ARCH_300))
> + lpcr_val = lpcr_val & ~(u64)LPCR_PECE1;
> +
> rc = opal_slw_set_reg(pir, SPRN_LPCR, lpcr_val);
> if (rc != 0)
> return rc;
> @@ -355,6 +365,15 @@ void power9_idle(void)
> }
>
> #ifdef CONFIG_HOTPLUG_CPU
> +static void pnv_program_cpu_hotplug_lpcr(unsigned int cpu, u64 lpcr_val)
> +{
> + u64 pir = get_hard_smp_processor_id(cpu);
> +
> + mtspr(SPRN_LPCR, lpcr_val);
> + if (cpu_has_feature(CPU_FTR_ARCH_300))
> + opal_slw_set_reg(pir, SPRN_LPCR, lpcr_val);

Is opal_slw_set_reg very heavyweight? If not, I would just remove the
POWER9 special casing entirely from both these functions, which follows
the principle of least surprise. Otherwise I guess it's reasonable.

Thanks for making those other changes, it looks good.

Reviewed-by: Nicholas Piggin <npiggin@gmail.com>

\
 
 \ /
  Last update: 2017-07-19 11:11    [W:0.266 / U:0.100 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site