lkml.org 
[lkml]   [2017]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH 3.16 067/178] gpio:mcp23s08 Fixed missing interrupts
3.16.46-rc1 review patch.  If anyone has any objections, please let me know.

------------------

From: Robert Middleton <robert.middleton@rm5248.com>

commit 2cd29f2387be70de9feb4c9f8dbc7c0bd55748ce upstream.

When an interrupt occurs on an MCP23S08 chip, the INTF register will only
contain one bit as causing the interrupt. If more than two pins change at
the same time on the chip, this causes one of the pins to not be reported.
This patch fixes the logic for checking if a pin has changed, so that
multiple pins will always cause more than one change.

Signed-off-by: Robert Middleton <robert.middleton@rm5248.com>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16:
- No support for level-triggered interrupts
- Use mcp->ops->read instead of mcp_read()
- Device pointer for logging is mcp->chip.dev]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
---
--- a/drivers/gpio/gpio-mcp23s08.c
+++ b/drivers/gpio/gpio-mcp23s08.c
@@ -340,8 +340,10 @@ mcp23s08_direction_output(struct gpio_ch
static irqreturn_t mcp23s08_irq(int irq, void *data)
{
struct mcp23s08 *mcp = data;
- int intcap, intf, i;
+ int intcap, intf, i, gpio, gpio_orig, intcap_mask;
unsigned int child_irq;
+ bool intf_set, intcap_changed, gpio_bit_changed,
+ gpio_set;

mutex_lock(&mcp->lock);
intf = mcp->ops->read(mcp, MCP_INTF);
@@ -359,13 +361,63 @@ static irqreturn_t mcp23s08_irq(int irq,
}

mcp->cache[MCP_INTCAP] = intcap;
+
+ /* This clears the interrupt(configurable on S18) */
+ if ((gpio = mcp->ops->read(mcp, MCP_GPIO)) < 0) {
+ mutex_unlock(&mcp->lock);
+ return IRQ_HANDLED;
+ }
+ gpio_orig = mcp->cache[MCP_GPIO];
+ mcp->cache[MCP_GPIO] = gpio;
mutex_unlock(&mcp->lock);

+ if (mcp->cache[MCP_INTF] == 0) {
+ /* There is no interrupt pending */
+ return IRQ_HANDLED;
+ }
+
+ dev_dbg(mcp->chip.dev,
+ "intcap 0x%04X intf 0x%04X gpio_orig 0x%04X gpio 0x%04X\n",
+ intcap, intf, gpio_orig, gpio);

for (i = 0; i < mcp->chip.ngpio; i++) {
- if ((BIT(i) & mcp->cache[MCP_INTF]) &&
- ((BIT(i) & intcap & mcp->irq_rise) ||
- (mcp->irq_fall & ~intcap & BIT(i)))) {
+ /* We must check all of the inputs on the chip,
+ * otherwise we may not notice a change on >=2 pins.
+ *
+ * On at least the mcp23s17, INTCAP is only updated
+ * one byte at a time(INTCAPA and INTCAPB are
+ * not written to at the same time - only on a per-bank
+ * basis).
+ *
+ * INTF only contains the single bit that caused the
+ * interrupt per-bank. On the mcp23s17, there is
+ * INTFA and INTFB. If two pins are changed on the A
+ * side at the same time, INTF will only have one bit
+ * set. If one pin on the A side and one pin on the B
+ * side are changed at the same time, INTF will have
+ * two bits set. Thus, INTF can't be the only check
+ * to see if the input has changed.
+ */
+
+ intf_set = BIT(i) & mcp->cache[MCP_INTF];
+ if (i < 8 && intf_set)
+ intcap_mask = 0x00FF;
+ else if (i >= 8 && intf_set)
+ intcap_mask = 0xFF00;
+ else
+ intcap_mask = 0x00;
+
+ intcap_changed = (intcap_mask &
+ (BIT(i) & mcp->cache[MCP_INTCAP])) !=
+ (intcap_mask & (BIT(i) & gpio_orig));
+ gpio_set = BIT(i) & mcp->cache[MCP_GPIO];
+ gpio_bit_changed = (BIT(i) & gpio_orig) !=
+ (BIT(i) & mcp->cache[MCP_GPIO]);
+
+ if (((gpio_bit_changed || intcap_changed) &&
+ (BIT(i) & mcp->irq_rise) && gpio_set) ||
+ ((gpio_bit_changed || intcap_changed) &&
+ (BIT(i) & mcp->irq_fall) && !gpio_set)) {
child_irq = irq_find_mapping(mcp->irq_domain, i);
handle_nested_irq(child_irq);
}
\
 
 \ /
  Last update: 2017-07-16 16:18    [W:1.332 / U:0.728 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site