lkml.org 
[lkml]   [2017]   [Jul]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V4] PCI: handle CRS returned by device after FLR
On Thu, Jul 06, 2017 at 05:07:14PM -0400, Sinan Kaya wrote:
> An endpoint is allowed to issue Configuration Request Retry Status (CRS)
> following a Function Level Reset (FLR) request to indicate that it is not
> ready to accept new requests.
>
> Seen a timeout message with Intel 750 NVMe drive and FLR reset.
>
> Kernel enables CRS visibility in pci_enable_crs() function for each bridge
> it discovers. The OS observes a special vendor ID read value of 0xFFFF0001
> in this case. We need to keep polling until this special read value
> disappears. pci_bus_read_dev_vendor_id() takes care of CRS handling for a
> given vendor id read request under the covers.

This patch isn't about how CRS works; we already have support for
that. So this paragraph is mostly extraneous and can be replaced by a
simple reference to CRS in the spec.

> Adding a vendor ID read if this is a physical function before attempting
> to read any other registers on the endpoint. A CRS indication will only
> be given if the address to be read is vendor ID register.
>
> Note that virtual functions report their vendor ID through another
> mechanism.

How VFs report vendor ID is irrelevant.

What *is* relevant is how FLR affects VFs. The SR-IOV spec, r1.1,
sec 2.2.2, says FLR doesn't affect a VF's existence in config space.

That suggests to me that reading a VF's PCI_COMMAND register after an
FLR should always return valid data (never ~0). I suppose an FLR VF
reset isn't instantaneous, though, so I suppose we do need the 100ms
delay. But maybe we should just return immediately after that,
without reading any VF config space?

pci_flr_wait() was added by 5adecf817dd6 ("PCI: Wait for up to 1000ms
after FLR reset"); maybe Alex has more insight into this.

> The spec is calling to wait up to 1 seconds if the device is sending CRS.
> The NVMe device seems to be requiring more. Relax this up to 60 seconds.
>
> Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
> ---
> drivers/pci/pci.c | 14 ++++++++++----
> 1 file changed, 10 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
> index aab9d51..83a9784 100644
> --- a/drivers/pci/pci.c
> +++ b/drivers/pci/pci.c
> @@ -3723,10 +3723,16 @@ static void pci_flr_wait(struct pci_dev *dev)
> int i = 0;
> u32 id;
>
> - do {
> - msleep(100);
> - pci_read_config_dword(dev, PCI_COMMAND, &id);
> - } while (i++ < 10 && id == ~0);
> + if (dev->is_virtfn) {
> + do {
> + msleep(100);
> + pci_read_config_dword(dev, PCI_COMMAND, &id);
> + } while (i++ < 10 && id == ~0);
> + } else {
> + if (!pci_bus_read_dev_vendor_id(dev->bus, dev->devfn, &id,
> + 60*1000))
> + id = ~0;
> + }
>
> if (id == ~0)
> dev_warn(&dev->dev, "Failed to return from FLR\n");
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

\
 
 \ /
  Last update: 2017-07-14 01:49    [W:0.102 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site