lkml.org 
[lkml]   [2017]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v6 2/2] fpga manager: Add Altera CvP driver
On Fri, Jun 9, 2017 at 3:22 AM, Anatolij Gustschin <agust@denx.de> wrote:
> Add FPGA manager driver for loading Arria-V/Cyclone-V/Stratix-V
> and Arria-10 FPGAs via CvP.
>

Thanks for an update. I'm fine with it...

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

...but just in case see comments below (you can address them if you want to).

> Signed-off-by: Anatolij Gustschin <agust@denx.de>
> ---
> Documentation/ABI/testing/sysfs-driver-altera-cvp | 8 +
> drivers/fpga/Kconfig | 7 +
> drivers/fpga/Makefile | 1 +
> drivers/fpga/altera-cvp.c | 500 ++++++++++++++++++++++
> 4 files changed, 516 insertions(+)
> create mode 100644 Documentation/ABI/testing/sysfs-driver-altera-cvp
> create mode 100644 drivers/fpga/altera-cvp.c
>
> diff --git a/Documentation/ABI/testing/sysfs-driver-altera-cvp b/Documentation/ABI/testing/sysfs-driver-altera-cvp
> new file mode 100644
> index 0000000..8cde64a
> --- /dev/null
> +++ b/Documentation/ABI/testing/sysfs-driver-altera-cvp
> @@ -0,0 +1,8 @@
> +What: /sys/bus/pci/drivers/altera-cvp/chkcfg
> +Date: May 2017
> +Kernel Version: 4.13
> +Contact: Anatolij Gustschin <agust@denx.de>
> +Description:
> + Contains either 1 or 0 and controls if configuration
> + error checking in altera-cvp driver is turned on or
> + off.
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index 942d276..2b38880 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -24,6 +24,13 @@ config FPGA_MGR_ICE40_SPI
> help
> FPGA manager driver support for Lattice iCE40 FPGAs over SPI.
>
> +config FPGA_MGR_ALTERA_CVP
> + tristate "Altera Arria-V/Cyclone-V/Stratix-V CvP FPGA Manager"
> + depends on PCI
> + help
> + FPGA manager driver support for Arria-V, Cyclone-V, Stratix-V
> + and Arria 10 Altera FPGAs using the CvP interface over PCIe.
> +
> config FPGA_MGR_ALTERA_PS_SPI
> tristate "Altera FPGA Passive Serial over SPI"
> depends on SPI || COMPILE_TEST
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index e75d357..e09895f 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -6,6 +6,7 @@
> obj-$(CONFIG_FPGA) += fpga-mgr.o
>
> # FPGA Manager Drivers
> +obj-$(CONFIG_FPGA_MGR_ALTERA_CVP) += altera-cvp.o
> obj-$(CONFIG_FPGA_MGR_ALTERA_PS_SPI) += altera-ps-spi.o
> obj-$(CONFIG_FPGA_MGR_ICE40_SPI) += ice40-spi.o
> obj-$(CONFIG_FPGA_MGR_SOCFPGA) += socfpga.o
> diff --git a/drivers/fpga/altera-cvp.c b/drivers/fpga/altera-cvp.c
> new file mode 100644
> index 0000000..08629ee
> --- /dev/null
> +++ b/drivers/fpga/altera-cvp.c
> @@ -0,0 +1,500 @@
> +/*
> + * FPGA Manager Driver for Altera Arria/Cyclone/Stratix CvP
> + *
> + * Copyright (C) 2017 DENX Software Engineering
> + *
> + * Anatolij Gustschin <agust@denx.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Manage Altera FPGA firmware using PCIe CvP.
> + * Firmware must be in binary "rbf" format.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/fpga/fpga-mgr.h>
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/sizes.h>
> +
> +#define CVP_BAR 0 /* BAR used for data transfer in memory mode */
> +#define CVP_DUMMY_WR 244 /* dummy writes to clear CvP state machine */
> +#define TIMEOUT_US 2000 /* CVP STATUS timeout for USERMODE polling */
> +
> +/* Vendor Specific Extended Capability Registers */
> +#define VSE_PCIE_EXT_CAP_ID 0x200
> +#define VSE_PCIE_EXT_CAP_ID_VAL 0x000b /* 16bit */
> +
> +#define VSE_CVP_STATUS 0x21c /* 32bit */
> +#define VSE_CVP_STATUS_CFG_RDY BIT(18) /* CVP_CONFIG_READY */
> +#define VSE_CVP_STATUS_CFG_ERR BIT(19) /* CVP_CONFIG_ERROR */
> +#define VSE_CVP_STATUS_CVP_EN BIT(20) /* ctrl block is enabling CVP */
> +#define VSE_CVP_STATUS_USERMODE BIT(21) /* USERMODE */
> +#define VSE_CVP_STATUS_CFG_DONE BIT(23) /* CVP_CONFIG_DONE */
> +#define VSE_CVP_STATUS_PLD_CLK_IN_USE BIT(24) /* PLD_CLK_IN_USE */
> +
> +#define VSE_CVP_MODE_CTRL 0x220 /* 32bit */
> +#define VSE_CVP_MODE_CTRL_CVP_MODE BIT(0) /* CVP (1) or normal mode (0) */
> +#define VSE_CVP_MODE_CTRL_HIP_CLK_SEL BIT(1) /* PMA (1) or fabric clock (0) */
> +#define VSE_CVP_MODE_CTRL_NUMCLKS_OFF 8 /* NUMCLKS bits offset */
> +#define VSE_CVP_MODE_CTRL_NUMCLKS_MASK GENMASK(15, 8)
> +
> +#define VSE_CVP_DATA 0x228 /* 32bit */
> +#define VSE_CVP_PROG_CTRL 0x22c /* 32bit */
> +#define VSE_CVP_PROG_CTRL_CONFIG BIT(0)
> +#define VSE_CVP_PROG_CTRL_START_XFER BIT(1)
> +
> +#define VSE_UNCOR_ERR_STATUS 0x234 /* 32bit */
> +#define VSE_UNCOR_ERR_CVP_CFG_ERR BIT(5) /* CVP_CONFIG_ERROR_LATCHED */
> +
> +#define DRV_NAME "altera-cvp"
> +#define ALTERA_CVP_MGR_NAME "Altera CvP FPGA Manager"
> +
> +/* Optional CvP config error status check for debugging */
> +static bool altera_cvp_chkcfg;
> +
> +struct altera_cvp_conf {
> + struct fpga_manager *mgr;
> + struct pci_dev *pci_dev;
> + void __iomem *map;
> + void (*write_data)(struct altera_cvp_conf *, u32);
> + char mgr_name[64];
> + u8 numclks;
> +};
> +
> +static enum fpga_mgr_states altera_cvp_state(struct fpga_manager *mgr)
> +{
> + struct altera_cvp_conf *conf = mgr->priv;
> + u32 status;
> +
> + pci_read_config_dword(conf->pci_dev, VSE_CVP_STATUS, &status);
> +
> + if (status & VSE_CVP_STATUS_CFG_DONE)
> + return FPGA_MGR_STATE_OPERATING;
> +
> + if (status & VSE_CVP_STATUS_CVP_EN)
> + return FPGA_MGR_STATE_POWER_UP;
> +
> + return FPGA_MGR_STATE_UNKNOWN;
> +}
> +
> +static void altera_cvp_write_data_iomem(struct altera_cvp_conf *conf, u32 val)
> +{
> + writel(val, conf->map);
> +}
> +
> +static void altera_cvp_write_data_config(struct altera_cvp_conf *conf, u32 val)
> +{
> + pci_write_config_dword(conf->pci_dev, VSE_CVP_DATA, val);
> +}
> +
> +/* switches between CvP clock and internal clock */
> +static void altera_cvp_dummy_write(struct altera_cvp_conf *conf)
> +{
> + unsigned int i;
> + u32 val;
> +
> + /* set 1 CVP clock cycle for every CVP Data Register Write */
> + pci_read_config_dword(conf->pci_dev, VSE_CVP_MODE_CTRL, &val);
> + val &= ~VSE_CVP_MODE_CTRL_NUMCLKS_MASK;
> + val |= 1 << VSE_CVP_MODE_CTRL_NUMCLKS_OFF;
> + pci_write_config_dword(conf->pci_dev, VSE_CVP_MODE_CTRL, val);
> +
> + for (i = 0; i < CVP_DUMMY_WR; i++)
> + conf->write_data(conf, 0); /* dummy data, could be any value */
> +}
> +
> +static int altera_cvp_wait_status(struct altera_cvp_conf *conf, u32 status_mask,
> + u32 status_val, int timeout_us)
> +{

> + unsigned int retries;

> + u32 val;
> +

> + retries = timeout_us / 10;
> + if (timeout_us % 10)
> + retries++;

> +
> + do {
> + pci_read_config_dword(conf->pci_dev, VSE_CVP_STATUS, &val);
> + if ((val & status_mask) == status_val)
> + return 0;
> +
> + /* use small usleep value to re-check and break early */
> + usleep_range(10, 11);

> + } while (--retries);

In previous message I told about an adjustment of the patter to your needs.
So, instead of using retries like in other cases, here you can do like
you did previously...

timeout_us -= 10;
} while (timeout_us > 0);

...and remove that divisions along with retries variable.

> +
> + return -ETIMEDOUT;
> +}
> +
> +static int altera_cvp_teardown(struct fpga_manager *mgr,
> + struct fpga_image_info *info)
> +{
> + struct altera_cvp_conf *conf = mgr->priv;
> + struct pci_dev *pdev = conf->pci_dev;
> + int ret;
> + u32 val;
> +
> + /* STEP 12 - reset START_XFER bit */
> + pci_read_config_dword(pdev, VSE_CVP_PROG_CTRL, &val);
> + val &= ~VSE_CVP_PROG_CTRL_START_XFER;
> + pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
> +
> + /* STEP 13 - reset CVP_CONFIG bit */
> + val &= ~VSE_CVP_PROG_CTRL_CONFIG;
> + pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
> +
> + /*
> + * STEP 14
> + * - set CVP_NUMCLKS to 1 and then issue CVP_DUMMY_WR dummy
> + * writes to the HIP
> + */
> + altera_cvp_dummy_write(conf); /* from CVP clock to internal clock */
> +
> + /* STEP 15 - poll CVP_CONFIG_READY bit for 0 with 10us timeout */
> + ret = altera_cvp_wait_status(conf, VSE_CVP_STATUS_CFG_RDY, 0, 10);
> + if (ret)
> + dev_err(&mgr->dev, "CFG_RDY == 0 timeout\n");
> +
> + return ret;
> +}
> +
> +static int altera_cvp_write_init(struct fpga_manager *mgr,
> + struct fpga_image_info *info,
> + const char *buf, size_t count)
> +{
> + struct altera_cvp_conf *conf = mgr->priv;
> + struct pci_dev *pdev = conf->pci_dev;
> + u32 iflags, val;
> + int ret;
> +

> + iflags = info ? info->flags : 0;
> +

You can remove this empty line, but it's matter of style here.

> + if (iflags & FPGA_MGR_PARTIAL_RECONFIG) {
> + dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
> + return -EINVAL;
> + }
> +
> + /* Determine allowed clock to data ratio */
> + if (iflags & FPGA_MGR_COMPRESSED_BITSTREAM)
> + conf->numclks = 8; /* ratio for all compressed images */
> + else if (iflags & FPGA_MGR_ENCRYPTED_BITSTREAM)
> + conf->numclks = 4; /* for uncompressed and encrypted images */
> + else
> + conf->numclks = 1; /* for uncompressed and unencrypted images */
> +

> + /* STEP 1 - read CVP status and check CVP_EN flag */

Btw, all these STEP X comments points to (probably) lack of
documentation how it's supposed to work.
Consider to add some if there is no yet.

> + pci_read_config_dword(pdev, VSE_CVP_STATUS, &val);
> + if (!(val & VSE_CVP_STATUS_CVP_EN)) {
> + dev_err(&mgr->dev, "CVP mode off: 0x%04x\n", val);
> + return -ENODEV;
> + }
> +
> + if (val & VSE_CVP_STATUS_CFG_RDY) {
> + dev_warn(&mgr->dev, "CvP already started, teardown first\n");
> + ret = altera_cvp_teardown(mgr, info);
> + if (ret)
> + return ret;
> + }
> +
> + /*
> + * STEP 2
> + * - set HIP_CLK_SEL and CVP_MODE (must be set in the order mentioned)
> + */
> + /* switch from fabric to PMA clock */
> + pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
> + val |= VSE_CVP_MODE_CTRL_HIP_CLK_SEL;
> + pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
> +
> + /* set CVP mode */
> + pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
> + val |= VSE_CVP_MODE_CTRL_CVP_MODE;
> + pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
> +
> + /*
> + * STEP 3
> + * - set CVP_NUMCLKS to 1 and issue CVP_DUMMY_WR dummy writes to the HIP
> + */
> + altera_cvp_dummy_write(conf);
> +
> + /* STEP 4 - set CVP_CONFIG bit */
> + pci_read_config_dword(pdev, VSE_CVP_PROG_CTRL, &val);
> + /* request control block to begin transfer using CVP */
> + val |= VSE_CVP_PROG_CTRL_CONFIG;
> + pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
> +
> + /* STEP 5 - poll CVP_CONFIG READY for 1 with 10us timeout */
> + ret = altera_cvp_wait_status(conf, VSE_CVP_STATUS_CFG_RDY,
> + VSE_CVP_STATUS_CFG_RDY, 10);
> + if (ret) {
> + dev_warn(&mgr->dev, "CFG_RDY == 1 timeout\n");
> + return ret;
> + }
> +
> + /*
> + * STEP 6
> + * - set CVP_NUMCLKS to 1 and issue CVP_DUMMY_WR dummy writes to the HIP
> + */
> + altera_cvp_dummy_write(conf);
> +
> + /* STEP 7 - set START_XFER */
> + pci_read_config_dword(pdev, VSE_CVP_PROG_CTRL, &val);
> + val |= VSE_CVP_PROG_CTRL_START_XFER;
> + pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
> +
> + /* STEP 8 - start transfer (set CVP_NUMCLKS for bitstream) */
> + pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
> + val &= ~VSE_CVP_MODE_CTRL_NUMCLKS_MASK;
> + val |= conf->numclks << VSE_CVP_MODE_CTRL_NUMCLKS_OFF;
> + pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
> +
> + return 0;
> +}
> +
> +static inline int altera_cvp_chk_error(struct fpga_manager *mgr, size_t bytes)
> +{
> + struct altera_cvp_conf *conf = mgr->priv;
> + u32 val;
> +
> + /* STEP 10 (optional) - check CVP_CONFIG_ERROR flag */
> + pci_read_config_dword(conf->pci_dev, VSE_CVP_STATUS, &val);
> + if (val & VSE_CVP_STATUS_CFG_ERR) {
> + dev_err(&mgr->dev, "CVP_CONFIG_ERROR after %zu bytes!\n",
> + bytes);
> + return -EPROTO;
> + }
> + return 0;
> +}
> +
> +static int altera_cvp_write(struct fpga_manager *mgr, const char *buf,
> + size_t count)
> +{
> + struct altera_cvp_conf *conf = mgr->priv;
> + const u32 *data;
> + size_t done, remaining;
> + int status = 0;
> + u32 mask;
> +
> + /* STEP 9 - write 32-bit data from RBF file to CVP data register */
> + data = (u32 *)buf;
> + remaining = count;
> + done = 0;
> +
> + while (remaining >= 4) {
> + conf->write_data(conf, *data++);
> + done += 4;
> + remaining -= 4;
> +
> + /*
> + * STEP 10 (optional) and STEP 11
> + * - check error flag
> + * - loop until data transfer completed
> + * Config images can be huge (more than 40 MiB), so
> + * only check after a new 4k data block has been written.
> + * This reduces the number of checks and speeds up the
> + * configuration process.
> + */
> + if (altera_cvp_chkcfg && !(done % SZ_4K)) {
> + status = altera_cvp_chk_error(mgr, done);
> + if (status < 0)
> + return status;
> + }
> + }
> +
> + /* write up to 3 trailing bytes, if any */
> + mask = BIT(remaining * 8) - 1;
> + if (mask)
> + conf->write_data(conf, *data & mask);
> +
> + if (altera_cvp_chkcfg)
> + status = altera_cvp_chk_error(mgr, count);
> +
> + return status;
> +}
> +
> +static int altera_cvp_write_complete(struct fpga_manager *mgr,
> + struct fpga_image_info *info)
> +{
> + struct altera_cvp_conf *conf = mgr->priv;
> + struct pci_dev *pdev = conf->pci_dev;
> + int ret;
> + u32 mask;
> + u32 val;
> +
> + ret = altera_cvp_teardown(mgr, info);
> + if (ret)
> + return ret;
> +
> + /* STEP 16 - check CVP_CONFIG_ERROR_LATCHED bit */
> + pci_read_config_dword(pdev, VSE_UNCOR_ERR_STATUS, &val);
> + if (val & VSE_UNCOR_ERR_CVP_CFG_ERR) {
> + dev_err(&mgr->dev, "detected CVP_CONFIG_ERROR_LATCHED!\n");
> + return -EPROTO;
> + }
> +
> + /* STEP 17 - reset CVP_MODE and HIP_CLK_SEL bit */
> + pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
> + val &= ~VSE_CVP_MODE_CTRL_HIP_CLK_SEL;
> + val &= ~VSE_CVP_MODE_CTRL_CVP_MODE;
> + pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
> +
> + /* STEP 18 - poll PLD_CLK_IN_USE and USER_MODE bits */
> + mask = VSE_CVP_STATUS_PLD_CLK_IN_USE | VSE_CVP_STATUS_USERMODE;
> + ret = altera_cvp_wait_status(conf, mask, mask, TIMEOUT_US);
> + if (ret)
> + dev_err(&mgr->dev, "PLD_CLK_IN_USE|USERMODE timeout\n");
> +
> + return ret;
> +}
> +
> +static const struct fpga_manager_ops altera_cvp_ops = {
> + .state = altera_cvp_state,
> + .write_init = altera_cvp_write_init,
> + .write = altera_cvp_write,
> + .write_complete = altera_cvp_write_complete,
> +};
> +
> +static ssize_t show_chkcfg(struct device_driver *dev, char *buf)
> +{
> + return snprintf(buf, 3, "%d\n", altera_cvp_chkcfg);
> +}
> +
> +static ssize_t store_chkcfg(struct device_driver *drv, const char *buf,
> + size_t count)
> +{
> + int ret;
> +
> + ret = kstrtobool(buf, &altera_cvp_chkcfg);
> + if (ret)
> + return ret;
> +
> + return count;
> +}
> +
> +static DRIVER_ATTR(chkcfg, 0600, show_chkcfg, store_chkcfg);
> +
> +static int altera_cvp_probe(struct pci_dev *pdev,
> + const struct pci_device_id *dev_id);
> +static void altera_cvp_remove(struct pci_dev *pdev);
> +
> +#define PCI_VENDOR_ID_ALTERA 0x1172
> +
> +static struct pci_device_id altera_cvp_id_tbl[] = {
> + { PCI_VDEVICE(ALTERA, PCI_ANY_ID) },
> + { }
> +};
> +MODULE_DEVICE_TABLE(pci, altera_cvp_id_tbl);
> +
> +static struct pci_driver altera_cvp_driver = {
> + .name = DRV_NAME,
> + .id_table = altera_cvp_id_tbl,
> + .probe = altera_cvp_probe,
> + .remove = altera_cvp_remove,
> +};
> +
> +static int altera_cvp_probe(struct pci_dev *pdev,
> + const struct pci_device_id *dev_id)
> +{
> + struct altera_cvp_conf *conf;
> + u16 cmd, val;
> + int ret;
> +
> + /*
> + * First check if this is the expected FPGA device. PCI config
> + * space access works without enabling the PCI device, memory
> + * space access is enabled further down.
> + */
> + pci_read_config_word(pdev, VSE_PCIE_EXT_CAP_ID, &val);
> + if (val != VSE_PCIE_EXT_CAP_ID_VAL) {
> + dev_err(&pdev->dev, "Wrong EXT_CAP_ID value 0x%x\n", val);
> + return -ENODEV;
> + }
> +
> + conf = devm_kzalloc(&pdev->dev, sizeof(*conf), GFP_KERNEL);
> + if (!conf)
> + return -ENOMEM;
> +
> + /*
> + * Enable memory BAR access. We cannot use pci_enable_device() here
> + * because it will make the driver unusable with FPGA devices that
> + * have additional big IOMEM resources (e.g. 4GiB BARs) on 32-bit
> + * platform. Such BARs will not have an assigned address range and
> + * pci_enable_device() will fail, complaining about not claimed BAR,
> + * even if the concerned BAR is not needed for FPGA configuration
> + * at all. Thus, enable the device via PCI config space command.
> + */
> + pci_read_config_word(pdev, PCI_COMMAND, &cmd);
> + if (!(cmd & PCI_COMMAND_MEMORY)) {
> + cmd |= PCI_COMMAND_MEMORY;
> + pci_write_config_word(pdev, PCI_COMMAND, cmd);
> + }
> +
> + ret = pci_request_region(pdev, CVP_BAR, "CVP");
> + if (ret) {
> + dev_err(&pdev->dev, "Requesting CVP BAR region failed\n");
> + goto err_disable;
> + }
> +
> + conf->pci_dev = pdev;
> + conf->write_data = altera_cvp_write_data_iomem;
> +
> + conf->map = pci_iomap(pdev, CVP_BAR, 0);
> + if (!conf->map) {
> + dev_warn(&pdev->dev, "Mapping CVP BAR failed\n");
> + conf->write_data = altera_cvp_write_data_config;
> + }
> +
> + snprintf(conf->mgr_name, sizeof(conf->mgr_name), "%s @%s",
> + ALTERA_CVP_MGR_NAME, pci_name(pdev));
> +
> + ret = fpga_mgr_register(&pdev->dev, conf->mgr_name,
> + &altera_cvp_ops, conf);
> + if (ret)
> + goto err_unmap;
> +
> + ret = driver_create_file(&altera_cvp_driver.driver,
> + &driver_attr_chkcfg);
> + if (ret) {
> + dev_err(&pdev->dev, "Can't create sysfs chkcfg file\n");
> + fpga_mgr_unregister(&pdev->dev);
> + goto err_unmap;
> + }
> +
> + return 0;
> +
> +err_unmap:
> + pci_iounmap(pdev, conf->map);
> + pci_release_region(pdev, CVP_BAR);
> +err_disable:
> + cmd &= ~PCI_COMMAND_MEMORY;
> + pci_write_config_word(pdev, PCI_COMMAND, cmd);
> + return ret;
> +}
> +
> +static void altera_cvp_remove(struct pci_dev *pdev)
> +{
> + struct fpga_manager *mgr = pci_get_drvdata(pdev);
> + struct altera_cvp_conf *conf = mgr->priv;
> + u16 cmd;
> +
> + driver_remove_file(&altera_cvp_driver.driver, &driver_attr_chkcfg);
> + fpga_mgr_unregister(&pdev->dev);
> + pci_iounmap(pdev, conf->map);
> + pci_release_region(pdev, CVP_BAR);
> + pci_read_config_word(pdev, PCI_COMMAND, &cmd);
> + cmd &= ~PCI_COMMAND_MEMORY;
> + pci_write_config_word(pdev, PCI_COMMAND, cmd);
> +}
> +
> +module_pci_driver(altera_cvp_driver);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Anatolij Gustschin <agust@denx.de>");
> +MODULE_DESCRIPTION("Module to load Altera FPGA over CvP");
> --
> 2.7.4
>



--
With Best Regards,
Andy Shevchenko

\
 
 \ /
  Last update: 2017-06-12 01:42    [W:0.078 / U:0.272 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site