lkml.org 
[lkml]   [2017]   [Jun]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/5] dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
Date
This patch adds the documentation of device tree bindings for STM32F7 I2C

Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
---
Change in V2
* Remove i2c-timing binding in order to use generic bindings SCL Rising
and Falling time instead
---
.../devicetree/bindings/i2c/i2c-stm32.txt | 29 +++++++++++++++++++---
1 file changed, 26 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
index 78eaf7b..3b54899 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
@@ -1,7 +1,9 @@
* I2C controller embedded in STMicroelectronics STM32 I2C platform

Required properties :
-- compatible : Must be "st,stm32f4-i2c"
+- compatible : Must be one of the following
+ - "st,stm32f4-i2c"
+ - "st,stm32f7-i2c"
- reg : Offset and length of the register set for the device
- interrupts : Must contain the interrupt id for I2C event and then the
interrupt id for I2C error.
@@ -14,8 +16,16 @@ Required properties :

Optional properties :
- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
- the default 100 kHz frequency will be used. As only Normal and Fast modes
- are supported, possible values are 100000 and 400000.
+ the default 100 kHz frequency will be used.
+ For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
+ 100000 and 400000.
+ For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
+ possible values are 100000, 400000 and 1000000.
+- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
+ (default: 25)
+- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
+ (default: 10)
+ I2C Timings are derived from these 2 values

Example :

@@ -31,3 +41,16 @@ Example :
pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
pinctrl-names = "default";
};
+
+ i2c@40005400 {
+ compatible = "st,stm32f7-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x40005400 0x400>;
+ interrupts = <31>,
+ <32>;
+ resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
+ clocks = <&rcc 1 CLK_I2C1>;
+ pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
+ pinctrl-names = "default";
+ };
--
1.9.1
\
 
 \ /
  Last update: 2017-06-20 13:43    [W:0.096 / U:2.412 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site