lkml.org 
[lkml]   [2017]   [Jun]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] tty/serial: atmel: make the driver DT only
Date
Now that AVR32 is gone, platform_data are not used to initialize the driver
anymore, remove that path from the driver. Also remove the now unused
struct atmel_uart_data.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
drivers/tty/serial/atmel_serial.c | 97 +++++++++++++------------------------
include/linux/platform_data/atmel.h | 11 -----
2 files changed, 33 insertions(+), 75 deletions(-)

diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 906e2b91bf57..1210a2632846 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -1655,72 +1655,55 @@ static void atmel_init_property(struct atmel_uart_port *atmel_port,
struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
- struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
-
- if (np) {
- /* DMA/PDC usage specification */
- if (of_property_read_bool(np, "atmel,use-dma-rx")) {
- if (of_property_read_bool(np, "dmas")) {
- atmel_port->use_dma_rx = true;
- atmel_port->use_pdc_rx = false;
- } else {
- atmel_port->use_dma_rx = false;
- atmel_port->use_pdc_rx = true;
- }
+
+ /* DMA/PDC usage specification */
+ if (of_property_read_bool(np, "atmel,use-dma-rx")) {
+ if (of_property_read_bool(np, "dmas")) {
+ atmel_port->use_dma_rx = true;
+ atmel_port->use_pdc_rx = false;
} else {
atmel_port->use_dma_rx = false;
- atmel_port->use_pdc_rx = false;
+ atmel_port->use_pdc_rx = true;
}
+ } else {
+ atmel_port->use_dma_rx = false;
+ atmel_port->use_pdc_rx = false;
+ }

- if (of_property_read_bool(np, "atmel,use-dma-tx")) {
- if (of_property_read_bool(np, "dmas")) {
- atmel_port->use_dma_tx = true;
- atmel_port->use_pdc_tx = false;
- } else {
- atmel_port->use_dma_tx = false;
- atmel_port->use_pdc_tx = true;
- }
+ if (of_property_read_bool(np, "atmel,use-dma-tx")) {
+ if (of_property_read_bool(np, "dmas")) {
+ atmel_port->use_dma_tx = true;
+ atmel_port->use_pdc_tx = false;
} else {
atmel_port->use_dma_tx = false;
- atmel_port->use_pdc_tx = false;
+ atmel_port->use_pdc_tx = true;
}
-
} else {
- atmel_port->use_pdc_rx = pdata->use_dma_rx;
- atmel_port->use_pdc_tx = pdata->use_dma_tx;
- atmel_port->use_dma_rx = false;
atmel_port->use_dma_tx = false;
+ atmel_port->use_pdc_tx = false;
}
-
}

static void atmel_init_rs485(struct uart_port *port,
struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
- struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
-
- if (np) {
- struct serial_rs485 *rs485conf = &port->rs485;
- u32 rs485_delay[2];
- /* rs485 properties */
- if (of_property_read_u32_array(np, "rs485-rts-delay",
- rs485_delay, 2) == 0) {
- rs485conf->delay_rts_before_send = rs485_delay[0];
- rs485conf->delay_rts_after_send = rs485_delay[1];
- rs485conf->flags = 0;
- }
-
- if (of_get_property(np, "rs485-rx-during-tx", NULL))
- rs485conf->flags |= SER_RS485_RX_DURING_TX;

- if (of_get_property(np, "linux,rs485-enabled-at-boot-time",
- NULL))
- rs485conf->flags |= SER_RS485_ENABLED;
- } else {
- port->rs485 = pdata->rs485;
+ struct serial_rs485 *rs485conf = &port->rs485;
+ u32 rs485_delay[2];
+ /* rs485 properties */
+ if (of_property_read_u32_array(np, "rs485-rts-delay",
+ rs485_delay, 2) == 0) {
+ rs485conf->delay_rts_before_send = rs485_delay[0];
+ rs485conf->delay_rts_after_send = rs485_delay[1];
+ rs485conf->flags = 0;
}

+ if (of_get_property(np, "rs485-rx-during-tx", NULL))
+ rs485conf->flags |= SER_RS485_RX_DURING_TX;
+
+ if (of_get_property(np, "linux,rs485-enabled-at-boot-time", NULL))
+ rs485conf->flags |= SER_RS485_ENABLED;
}

static void atmel_set_ops(struct uart_port *port)
@@ -2402,7 +2385,6 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
{
int ret;
struct uart_port *port = &atmel_port->uart;
- struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);

atmel_init_property(atmel_port, pdev);
atmel_set_ops(port);
@@ -2410,24 +2392,17 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
atmel_init_rs485(port, pdev);

port->iotype = UPIO_MEM;
- port->flags = UPF_BOOT_AUTOCONF;
+ port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
port->ops = &atmel_pops;
port->fifosize = 1;
port->dev = &pdev->dev;
port->mapbase = pdev->resource[0].start;
port->irq = pdev->resource[1].start;
port->rs485_config = atmel_config_rs485;
+ port->membase = NULL;

memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));

- if (pdata && pdata->regs) {
- /* Already mapped by setup code */
- port->membase = pdata->regs;
- } else {
- port->flags |= UPF_IOREMAP;
- port->membase = NULL;
- }
-
/* for console, the clock could already be configured */
if (!atmel_port->clk) {
atmel_port->clk = clk_get(&pdev->dev, "usart");
@@ -2761,19 +2736,13 @@ static int atmel_serial_probe(struct platform_device *pdev)
{
struct atmel_uart_port *atmel_port;
struct device_node *np = pdev->dev.of_node;
- struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
void *data;
int ret = -ENODEV;
bool rs485_enabled;

BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));

- if (np)
- ret = of_alias_get_id(np, "serial");
- else
- if (pdata)
- ret = pdata->num;
-
+ ret = of_alias_get_id(np, "serial");
if (ret < 0)
/* port id not found in platform data nor device-tree aliases:
* auto-enumerate it */
diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
index 70c5c766628e..cdceb4d4ef9d 100644
--- a/include/linux/platform_data/atmel.h
+++ b/include/linux/platform_data/atmel.h
@@ -7,8 +7,6 @@
#ifndef __ATMEL_H__
#define __ATMEL_H__

-#include <linux/serial.h>
-
/* Compact Flash */
struct at91_cf_data {
int irq_pin; /* I/O IRQ */
@@ -21,15 +19,6 @@ struct at91_cf_data {
#define AT91_IDE_SWAP_A0_A2 0x02
};

- /* Serial */
-struct atmel_uart_data {
- int num; /* port num */
- short use_dma_tx; /* use transmit DMA? */
- short use_dma_rx; /* use receive DMA? */
- void __iomem *regs; /* virt. base address, if any */
- struct serial_rs485 rs485; /* rs485 settings */
-};
-
/* FIXME: this needs a better location, but gets stuff building again */
#ifdef CONFIG_ATMEL_PM
extern int at91_suspend_entering_slow_clock(void);
--
2.11.0
\
 
 \ /
  Last update: 2017-06-13 15:41    [W:0.057 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site