lkml.org 
[lkml]   [2017]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v2] net: fec: add post PHY reset delay DT property
Date
From: Quentin Schulz <quentin.schulz@free-electrons.com> Sent: Tuesday, May 23, 2017 5:48 PM
>Some PHY require to wait for a bit after the reset GPIO has been toggled. This
>adds support for the DT property `phy-reset-post-delay` which gives the delay
>in milliseconds to wait after reset.
>
>If the DT property is not given, no delay is observed. Post reset delay greater
>than 1000ms are invalid.
>
>Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
>---
>
>v2:
> - return -EINVAL when phy-reset-post-delay is greater than 1000ms
> instead of defaulting to 1ms,
> - remove `default to 1ms` when phy-reset-post-delay > 1000Ms from DT
> binding doc and commit log,
> - move phy-reset-post-delay property reading before
> devm_gpio_request_one(),
>
> Documentation/devicetree/bindings/net/fsl-fec.txt | 4 ++++
> drivers/net/ethernet/freescale/fec_main.c | 16 +++++++++++++++-
> 2 files changed, 19 insertions(+), 1 deletion(-)
>
>diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt
>b/Documentation/devicetree/bindings/net/fsl-fec.txt
>index a1e3693cca16..6f55bdd52f8a 100644
>--- a/Documentation/devicetree/bindings/net/fsl-fec.txt
>+++ b/Documentation/devicetree/bindings/net/fsl-fec.txt
>@@ -15,6 +15,10 @@ Optional properties:
> - phy-reset-active-high : If present then the reset sequence using the GPIO
> specified in the "phy-reset-gpios" property is reversed (H=reset state,
> L=operation state).
>+- phy-reset-post-delay : Post reset delay in milliseconds. If present
>+then
>+ a delay of phy-reset-post-delay milliseconds will be observed after
>+the
>+ phy-reset-gpios has been toggled. Can be omitted thus no delay is
>+ observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
> - phy-supply : regulator that powers the Ethernet PHY.
> - phy-handle : phandle to the PHY device connected to this device.
> - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
>diff --git a/drivers/net/ethernet/freescale/fec_main.c
>b/drivers/net/ethernet/freescale/fec_main.c
>index 56a563f90b0b..f7c8649fd28f 100644
>--- a/drivers/net/ethernet/freescale/fec_main.c
>+++ b/drivers/net/ethernet/freescale/fec_main.c
>@@ -3192,7 +3192,7 @@ static int fec_reset_phy(struct platform_device
>*pdev) {
> int err, phy_reset;
> bool active_high = false;
>- int msec = 1;
>+ int msec = 1, phy_post_delay = 0;
> struct device_node *np = pdev->dev.of_node;
>
> if (!np)
>@@ -3209,6 +3209,11 @@ static int fec_reset_phy(struct platform_device
>*pdev)
> else if (!gpio_is_valid(phy_reset))
> return 0;
>
>+ err = of_property_read_u32(np, "phy-reset-post-delay",
>&phy_post_delay);
>+ /* valid reset duration should be less than 1s */
>+ if (!err && phy_post_delay > 1000)
>+ return -EINVAL;
>+
> active_high = of_property_read_bool(np, "phy-reset-active-high");
>
> err = devm_gpio_request_one(&pdev->dev, phy_reset, @@ -3226,6
>+3231,15 @@ static int fec_reset_phy(struct platform_device *pdev)
>
> gpio_set_value_cansleep(phy_reset, !active_high);
>
>+ if (!phy_post_delay)
>+ return 0;
>+
>+ if (phy_post_delay > 20)
>+ msleep(phy_post_delay);
>+ else
>+ usleep_range(phy_post_delay * 1000,
>+ phy_post_delay * 1000 + 1000);
>+
> return 0;
> }
> #else /* CONFIG_OF */
>--
>2.11.0

It looks fine.
Acked-by: Fugang Duan <fugang.duan@nxp.com>

\
 
 \ /
  Last update: 2017-05-24 04:19    [W:0.079 / U:0.436 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site