lkml.org 
[lkml]   [2017]   [May]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC PATCH 01/11] dt-bindings: update the binding for Allwinner H3 TVE support
Date
Allwinner H3 features a "DE2.0" and a TV Encoder.

Add device tree bindings for the following parts:
- H3 TCONs
- H3 Mixers
- The connection between H3 TCONs and H3 Mixers
- H3 TV Encoder
- H3 Display engine

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
.../bindings/display/sunxi/sun4i-drm.txt | 47 ++++++++++++++++++++--
1 file changed, 43 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
index 66b85a195ef2..52781943713b 100644
--- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
+++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
@@ -21,7 +21,9 @@ The TV Encoder supports the composite and VGA output. It is one end of
the pipeline.

Required properties:
- - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
+ - compatible: value must be either:
+ * allwinner,sun4i-a10-tv-encoder
+ * allwinner,sun8i-h3-tv-encoder
- reg: base address and size of memory-mapped region
- clocks: the clocks driving the TV encoder
- resets: phandle to the reset controller driving the encoder
@@ -30,6 +32,13 @@ Required properties:
Documentation/devicetree/bindings/media/video-interfaces.txt. The
first port should be the input endpoint.

+For "allwinner,sun4i-a10-tv-encoder", there is only one clock required,
+and it's not named.
+
+For "allwinner,sun8i-h3-tv-encoder", these clocks are needed:
+ - 'bus': the AHB bus clock of TVE
+ - 'mod': the mod clock of TVE
+
TCON
----

@@ -41,29 +50,51 @@ Required properties:
* allwinner,sun6i-a31-tcon
* allwinner,sun6i-a31s-tcon
* allwinner,sun8i-a33-tcon
+ * allwinner,sun8i-h3-tcon0
+ * allwinner,sun8i-h3-tcon1
* allwinner,sun8i-v3s-tcon
- reg: base address and size of memory-mapped region
- interrupts: interrupt associated to this IP
- clocks: phandles to the clocks feeding the TCON. Three are needed:
- 'ahb': the interface clocks
- - 'tcon-ch0': The clock driving the TCON channel 0
- resets: phandles to the reset controllers driving the encoder
- "lcd": the reset line for the TCON channel 0

- clock-names: the clock names mentioned above
- reset-names: the reset names mentioned above
- - clock-output-names: Name of the pixel clock created

- ports: A ports node with endpoint definitions as defined in
Documentation/devicetree/bindings/media/video-interfaces.txt. The
first port should be the input endpoint, the second one the output

+ In the situation of Display Engine 2.0 that the connection between
+ the mixer and the TCON can be swapped, the input should have two
+ endpoints. The first is the default mixer connected to the TCON,
+ the second the mixer which will be connected to the TCON if the
+ swap bit is set.
+
The output should have two endpoints. The first is the block
connected to the TCON channel 0 (usually a panel or a bridge), the
second the block connected to the TCON channel 1 (usually the TV
encoder)

-On SoCs other than the A33 and V3s, there is one more clock required:
+For the following compatibles:
+ * allwinner,sun5i-a13-tcon
+ * allwinner,sun6i-a31-tcon
+ * allwinner,sun6i-a31s-tcon
+ * allwinner,sun8i-a33-tcon
+ * allwinner,sun8i-v3s-tcon
+there is one more clock and one more property required:
+ - clocks:
+ - 'tcon-ch0': The clock driving the TCON channel 0
+ - clock-output-names: Name of the pixel clock created
+
+For the following compatibles:
+ * allwinner,sun5i-a13-tcon
+ * allwinner,sun6i-a31-tcon
+ * allwinner,sun6i-a31s-tcon
+ * allwinner,sun8i-h3-tcon0
+there is one more clock required:
- 'tcon-ch1': The clock driving the TCON channel 1

DRC
@@ -158,6 +189,8 @@ supported.
Required properties:
- compatible: value must be one of:
* allwinner,sun8i-v3s-de2-mixer
+ * allwinner,sun8i-h3-de2-mixer0
+ * allwinner,sun8i-h3-de2-mixer1
- reg: base address and size of the memory-mapped region.
- clocks: phandles to the clocks feeding the mixer
* bus: the mixer interface clock
@@ -169,6 +202,11 @@ Required properties:
Documentation/devicetree/bindings/media/video-interfaces.txt. The
first port should be the input endpoints, the second one the output

+ In the situation of Display Engine 2.0 that the connection between
+ the mixer and the TCON can be swapped, the output should have two
+ endpoints. The first is the default TCON connected to the mixer,
+ the second the TCON which will be connected to the mixer if the
+ swap bit is set.

Display Engine Pipeline
-----------------------
@@ -183,6 +221,7 @@ Required properties:
* allwinner,sun6i-a31-display-engine
* allwinner,sun6i-a31s-display-engine
* allwinner,sun8i-a33-display-engine
+ * allwinner,sun8i-h3-display-engine
* allwinner,sun8i-v3s-display-engine

- allwinner,pipelines: list of phandle to the display engine
--
2.12.2
\
 
 \ /
  Last update: 2017-05-17 18:44    [W:0.256 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site