lkml.org 
[lkml]   [2017]   [May]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v3] ARM: dts: at91: sama5d2: add m_can nodes
Date
Hi Alexandre,

> -----Original Message-----
> From: Alexandre Belloni [mailto:alexandre.belloni@free-electrons.com]
> Sent: 2017年5月15日 17:44
> To: Wenyou Yang - A41535 <Wenyou.Yang@microchip.com>
> Cc: Nicolas Ferre - M43238 <Nicolas.Ferre@microchip.com>; Rob Herring
> <robh+dt@kernel.org>; Pawel Moll <pawel.moll@arm.com>; Mark Rutland
> <mark.rutland@arm.com>; Ian Campbell <ijc+devicetree@hellion.org.uk>; Kumar
> Gala <galak@codeaurora.org>; Russell King <linux@arm.linux.org.uk>; linux-
> kernel@vger.kernel.org; linux-can@vger.kernel.org; Oliver Hartkopp
> <socketcan@hartkopp.net>; devicetree@vger.kernel.org; Quentin Schulz
> <quentin.schulz@free-electrons.com>; Wenyou Yang - A41535
> <Wenyou.Yang@microchip.com>; linux-arm-kernel@lists.infradead.org
> Subject: Re: [PATCH v3] ARM: dts: at91: sama5d2: add m_can nodes
>
> On 24/04/2017 at 09:12:17 +0800, Wenyou Yang wrote:
> > Add nodes to support the Controller Area Network(M_CAN) on SAMA5D2.
> > The version of M_CAN IP core is 3.1.0 (CREL = 0x31040730).
> >
> > As said in SAMA5D2 datasheet, the CAN clock is recommended to use
> > frequencies of 20, 40 or 80 MHz. To achieve these frequencies, PMC
> > GCLK3 must select the UPLLCK(480 MHz) as source clock and divide by
> > 24, 12, or 6. So, the "assigned-clock-rates" property has three
> > options: 20000000, 40000000, and 80000000.
> > The "assigned-clock-parents" property should be referred to utmi
> > fixedly.
> >
> > The MSBs [bits 31:16] of the CAN Message RAM for CAN0 and CAN1 are
> > default configured in 0x00200000. To avoid conflict with SRAM map for
> > PM, change them to 0x00210000 in the AT91Bootstrap via setting the CAN
> > Memories Address-based Register(SFR_CAN) of SFR.
> >
> > Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> > Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
> > ---
> > The patch is tested on SAMA5D2 Xplained and based on the patch set,
> > 1. [PATCH v4 1/7] can: m_can: Disabled Interrupt Line 1
> > http://marc.info/?l=linux-can&m=149165343604033&w=2
> >
> > Changes in v3:
> > - Add Tested-by tag.
> > - Change the number of Rx Rx Buffers, Tx Buffers and Tx Event FIFO
> > to maximum.
> >
> > Changes in v2:
> > - Configures 10 TX Event FIFO elements and 10 TX Buffers/FIFO slots,
> > because the TXE FIFO is needed to be configured.
> > - Configure the offset of Message RAM for CAN1 followed from CAN0's.
> >
> > arch/arm/boot/dts/at91-sama5d2_xplained.dts | 24 +++++++++++++
> > arch/arm/boot/dts/sama5d2.dtsi | 56
> +++++++++++++++++++++++++++++
> > 2 files changed, 80 insertions(+)
> >
>
> It didn't apply cleanly, can you please verify
> https://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux.git/log/?h=at91-dt

Verified, it works.

Thank you for your effort.


BTW, it will be better take the patch to add the config.
[PATCH v2] ARM: at91/defconfig: add MCAN driver to sama5_defconfig
I just submitted.

>
> --
> Alexandre Belloni, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com


Best Regards,
Wenyou Yang
\
 
 \ /
  Last update: 2017-05-15 12:18    [W:0.068 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site