lkml.org 
[lkml]   [2017]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH v2 11/18] arm64: dts: meson-gxbb-odroidc2: Fix node order
    Date
    Sort nodes referenced by label alphabetically.

    Signed-off-by: Andreas Färber <afaerber@suse.de>
    ---
    v1 -> v2:
    * Rebased (new nodes added)

    .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 108 ++++++++++-----------
    1 file changed, 54 insertions(+), 54 deletions(-)

    diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
    index 54a9c6a6b392..d147c853ab05 100644
    --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
    +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
    @@ -137,16 +137,6 @@
    };
    };

    -&scpi_clocks {
    - status = "disabled";
    -};
    -
    -&uart_AO {
    - status = "okay";
    - pinctrl-0 = <&uart_ao_a_pins>;
    - pinctrl-names = "default";
    -};
    -
    &ethmac {
    status = "okay";
    pinctrl-0 = <&eth_rgmii_pins>;
    @@ -172,6 +162,33 @@
    };
    };

    +&gpio_ao {
    + /*
    + * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
    + * to be turned high in order to be detected by the USB Controller
    + * This signal should be handled by a USB specific power sequence
    + * in order to reset the Hub when USB bus is powered down.
    + */
    + usb-hub {
    + gpio-hog;
    + gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
    + output-high;
    + line-name = "usb-hub-reset";
    + };
    +};
    +
    +&i2c_A {
    + status = "okay";
    + pinctrl-0 = <&i2c_a_pins>;
    + pinctrl-names = "default";
    +};
    +
    +&ir {
    + status = "okay";
    + pinctrl-0 = <&remote_input_ao_pins>;
    + pinctrl-names = "default";
    +};
    +
    &pinctrl_aobus {
    gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
    "USB HUB nRESET", "USB OTG Power En",
    @@ -223,55 +240,15 @@
    "";
    };

    -&ir {
    - status = "okay";
    - pinctrl-0 = <&remote_input_ao_pins>;
    - pinctrl-names = "default";
    -};
    -
    -&i2c_A {
    - status = "okay";
    - pinctrl-0 = <&i2c_a_pins>;
    - pinctrl-names = "default";
    -};
    -
    -&gpio_ao {
    - /*
    - * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
    - * to be turned high in order to be detected by the USB Controller
    - * This signal should be handled by a USB specific power sequence
    - * in order to reset the Hub when USB bus is powered down.
    - */
    - usb-hub {
    - gpio-hog;
    - gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
    - output-high;
    - line-name = "usb-hub-reset";
    - };
    -};
    -
    -&usb0_phy {
    - status = "okay";
    - phy-supply = <&usb_otg_pwr>;
    -};
    -
    -&usb1_phy {
    - status = "okay";
    -};
    -
    -&usb0 {
    - status = "okay";
    -};
    -
    -&usb1 {
    - status = "okay";
    -};
    -
    &saradc {
    status = "okay";
    vref-supply = <&vcc1v8>;
    };

    +&scpi_clocks {
    + status = "disabled";
    +};
    +
    /* SD */
    &sd_emmc_b {
    status = "okay";
    @@ -309,3 +286,26 @@
    vmmc-supply = <&vcc3v3>;
    vqmmc-supply = <&vcc1v8>;
    };
    +
    +&uart_AO {
    + status = "okay";
    + pinctrl-0 = <&uart_ao_a_pins>;
    + pinctrl-names = "default";
    +};
    +
    +&usb0_phy {
    + status = "okay";
    + phy-supply = <&usb_otg_pwr>;
    +};
    +
    +&usb1_phy {
    + status = "okay";
    +};
    +
    +&usb0 {
    + status = "okay";
    +};
    +
    +&usb1 {
    + status = "okay";
    +};
    --
    2.12.0
    \
     
     \ /
      Last update: 2017-05-13 16:37    [W:4.519 / U:0.068 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site