lkml.org 
[lkml]   [2017]   [May]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] usb-musb: keep VBUS on when device is disconnected
* Bin Liu <b-liu@ti.com> [170511 12:23]:
> On Thu, May 11, 2017 at 02:10:05PM -0500, Bin Liu wrote:
> [...]
> > > > > The otg state machine implementation in the musb drivers are kind of strange.
> > > > > OTG_STATE_A_WAIT_BCON suppose to be a steady state when no usb device is
> > > > > attached, but the musb drivers use it as a transient state to handle error
> > > > > cases, such as overcurrent ot HNP timeout, which is done in the 'case
> > > > > OTG_STATE_A_WAIT_BCON' branch in otg_timer() (or dsps_check_status() for dsps
> > > > > glue).
> > > > >
> > > > > Then later when 2f3fd2c5bde1 adds
> > > > >
> > > > > - /* Poll for ID change in OTG port mode */
> > > > > - if (musb->xceiv->otg->state == OTG_STATE_B_IDLE &&
> > > > > - musb->port_mode == MUSB_PORT_MODE_DUAL_ROLE)
> > > > > + /* Poll for ID change and connect */
> > > > > + switch (musb->xceiv->otg->state) {
> > > > > + case OTG_STATE_B_IDLE:
> > > > > + case OTG_STATE_A_WAIT_BCON:
> > > > > mod_timer(&glue->timer, jiffies +
> > > > > msecs_to_jiffies(wrp->poll_timeout));
> > > > > + break;
> > > > >
> > > > > which causes dsps_check_status (or otg_timer()) got called for a normal
> > > > > condition with OTG_STATE_A_WAIT_BCON, then turns off VBUS...
> > > > >
> > > > > Will try to see how to solve this...
> > > >
> > > > Maybe we just need to add back the earlier check for non-OTG devices
> > > > "musb->port_mode == MUSB_PORT_MODE_DUAL_ROLE" into case
> > > > OTG_STATE_A_WAIT_BCON?
> > >
> > > Not sure if it will work. The check is to kick out device-only mode.
> > > DUAL_ROLE means both OTG and host-only.
> > >
> > > >
> > > > Not sure if am335x configured with host port ever idle that way,
> > > > but maybe VBUS can be kept on with musb idle.
> > >
> > > Just tried to remove
> > >
> > > + case OTG_STATE_A_WAIT_BCON:
> > >
> > > for the polling, but the port stops detecting device attach, musb
> > > power/devctl registers are good, trying to see why... maybe related to
> > > PM state?
> >
> > usb_otg_hs is idle, so not able to detect attach. So need to get the
> > timer rolling in here to make it detect working.
> > Maybe need to add a flag in dsps_check_status() to not turn off vbus in
> > this case? Really don't like the idea...

Yeah that's what I recall too. The timer is needed until the m3 can
implement an irqchip and we can set that up as the irq for the host
only port.

> I am not sure I gave out the picture clearly.
>
> Before added the runtime PM support, in host mode (devctl=0x19) the
> otg_timer is stopped, the controller is ready to detect attach.
>
> Later when added the runtime PM support, usb_otg_hs hwmod becomes idle
> when a device is detached, so the otg_timer is needed to keep hwmod
> enable/idle periodically to detect attach, which triggers the issue
> because otg_timer() turns off vbus unconditionally when otg state is
> OTG_STATE_A_WAIT_BCON.

I wonder if just keeping VBUS on longer in OTG_STATE_A_WAIT_BCON
solves this issue? It seems the issue is with modems that get
reconfigured after the initial enumeration?

We could poll for new devices every 2 seconds, if anything is seen
on the bus, keep VBUS on at least 20 seconds, then if nothing is
found, poll every 2 seconds again.

Regards,

Tony

\
 
 \ /
  Last update: 2017-05-11 21:39    [W:0.088 / U:0.420 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site