lkml.org 
[lkml]   [2017]   [Mar]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] mmc: core: Do not hold re-tuning during CMD6 commands
From
Date
On Fri, 2017-03-24 at 11:19 +0200, Adrian Hunter wrote:
> On 24/03/17 10:32, Chaotian Jing wrote:
> > On Fri, 2017-03-24 at 09:52 +0200, Adrian Hunter wrote:
> >> On 24/03/17 08:19, Chaotian Jing wrote:
> >>> this patch is refine for 'commit c6dbab9cb58f ("mmc: core: Hold re-tuning
> >>> during switch commands")'
> >>> Since it has 3 retries at max for CMD6, if the first CMD6 got CRC error,
> >>> then should do re-tune before the next CMD6 was sent.
> >>>
> >>> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> >>> ---
> >>> drivers/mmc/core/mmc_ops.c | 3 +--
> >>> 1 file changed, 1 insertion(+), 2 deletions(-)
> >>>
> >>> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
> >>> index fe80f26..6931927 100644
> >>> --- a/drivers/mmc/core/mmc_ops.c
> >>> +++ b/drivers/mmc/core/mmc_ops.c
> >>> @@ -534,8 +534,6 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
> >>> bool use_r1b_resp = use_busy_signal;
> >>> unsigned char old_timing = host->ios.timing;
> >>>
> >>> - mmc_retune_hold(host);
> >>> -
> >>> /*
> >>> * If the cmd timeout and the max_busy_timeout of the host are both
> >>> * specified, let's validate them. A failure means we need to prevent
> >>> @@ -567,6 +565,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
> >>> cmd.sanitize_busy = true;
> >>>
> >>> err = mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
> >>> + mmc_retune_hold(host);
> >>
> >> That is not how mmc_retune_hold() works, you need mmc_retune_hold_now() as
> >> it is here:
> >>
> >> https://marc.info/?l=linux-mmc&m=148940903816582
> >>
> >> But using "retries" with commands that have busy-waiting on the data line
> >> doesn't make much sense anyway. Particularly with CRC errors, I would
> >> expect the card is actually busily doing the switch and we need only to wait
> >> for it. The same can be true for timeout errors. For some CMD6 we might
> >> need to send CMD12 if the card is busy after an error. I would prefer an
> >> explicit attempt at recovery from CMD6 errors.
> >>
> >
> > It's the host driver's responsibility to ensure card is not in busy
> > state before issue the next R1B command, or the MMC core layer needs do
> > extra check/waiting before issue a R1B command.
>
> Better to deal with cards stuck in busy from the places where busy-waiting
> is expected.
>
Yes, if a R1B command got response CRC error, we can do busy-waiting in
the error hander funtion(mmc_wait_for_req_done())
> > I think the purpose of "re-tune" is trying to cover particular case(eg.
> > voltage fluctuate or EMI or some glitch of host/device which caused CRC
> > error)
>
> No, re-tuning is to compensate for drift caused primarily by temperature change.
>
Yes, by JEDEC spec, temperature change cause timing drift of EMMC
device, but, as you mentioned, maybe I have a hardware problem of host,
but needs Software to cover it. so that we are doing our best to do
re-tune if got CRC error. if could recover it, then it's better than
system hung.
> > error) , but in such cases, too many cases are disable re-tune function
> > by mmc_retune_hold(), for example, in this case, if a response CRC error
> > got then we never have chance to recover it. then cause system cannot
> > access emmc or suspend/resume fail.
>
> Maybe you have a hardware problem.
>


\
 
 \ /
  Last update: 2017-03-24 10:41    [W:0.062 / U:0.444 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site