lkml.org 
[lkml]   [2017]   [Mar]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3 2/2] drm/panel: add innolux,p079zca panel driver
can you add bps here too?

On Tue, Mar 21, 2017 at 6:53 PM, Chris Zhong <zyw@rock-chips.com> wrote:
> Support Innolux P079ZCA 7.85" 768x1024 TFT LCD panel, it is a MIPI DSI
> panel.
>
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
> Reviewed-by: Sean Paul <seanpaul@chromium.org>
> Tested-by: Brian Norris <briannorris@chromium.org>
> ---
>
> Changes in v3:
> - printk err after regulator_disable(innolux->supply)
>
> Changes in v2:
> - add some error check
> - always use Low power mode to send commend
> - add comments for all the sleep
> - use DRM_DEV_ERROR instead of dev_err
>
> drivers/gpu/drm/panel/Kconfig | 11 +
> drivers/gpu/drm/panel/Makefile | 1 +
> drivers/gpu/drm/panel/panel-innolux-p079zca.c | 345 ++++++++++++++++++++++++++
> 3 files changed, 357 insertions(+)
> create mode 100644 drivers/gpu/drm/panel/panel-innolux-p079zca.c
>
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 62aba97..99dd010 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -18,6 +18,17 @@ config DRM_PANEL_SIMPLE
> that it can be automatically turned off when the panel goes into a
> low power state.
>
> +config DRM_PANEL_INNOLUX_P079ZCA
> + tristate "Innolux P079ZCA panel"
> + depends on OF
> + depends on DRM_MIPI_DSI
> + depends on BACKLIGHT_CLASS_DEVICE
> + help
> + Say Y here if you want to enable support for Innolux P079ZCA
> + TFT-LCD modules. The panel has a 1024x768 resolution and uses
> + 24 bit RGB per pixel. It provides a MIPI DSI interface to
> + the host and has a built-in LED backlight.
> +
> config DRM_PANEL_JDI_LT070ME05000
> tristate "JDI LT070ME05000 WUXGA DSI panel"
> depends on OF
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index a5c7ec0..bda2aa4 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -1,4 +1,5 @@
> obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
> +obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
> obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
> obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
> obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o
> diff --git a/drivers/gpu/drm/panel/panel-innolux-p079zca.c b/drivers/gpu/drm/panel/panel-innolux-p079zca.c
> new file mode 100644
> index 0000000..9f3423a0
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-innolux-p079zca.c
> @@ -0,0 +1,345 @@
> +/*
> + * Copyright (c) 2017, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/backlight.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <drm/drmP.h>
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_panel.h>
> +
> +#include <video/mipi_display.h>
> +
> +struct innolux_panel {
> + struct drm_panel base;
> + struct mipi_dsi_device *link;
> +
> + struct backlight_device *backlight;
> + struct regulator *supply;
> + struct gpio_desc *enable_gpio;
> +
> + bool prepared;
> + bool enabled;
> +};
> +
> +static inline struct innolux_panel *to_innolux_panel(struct drm_panel *panel)
> +{
> + return container_of(panel, struct innolux_panel, base);
> +}
> +
> +static int innolux_panel_disable(struct drm_panel *panel)
> +{
> + struct innolux_panel *innolux = to_innolux_panel(panel);
> + int err;
> +
> + if (!innolux->enabled)
> + return 0;
> +
> + if (innolux->backlight) {
> + innolux->backlight->props.power = FB_BLANK_POWERDOWN;
> + backlight_update_status(innolux->backlight);
> + }
> +
> + err = mipi_dsi_dcs_set_display_off(innolux->link);
> + if (err < 0)
> + DRM_DEV_ERROR(panel->dev, "failed to set display off: %d\n",
> + err);
> +
> + innolux->enabled = false;
> +
> + return 0;
> +}
> +
> +static int innolux_panel_unprepare(struct drm_panel *panel)
> +{
> + struct innolux_panel *innolux = to_innolux_panel(panel);
> + int err;
> +
> + if (!innolux->prepared)
> + return 0;
> +
> + err = mipi_dsi_dcs_enter_sleep_mode(innolux->link);
> + if (err < 0) {
> + DRM_DEV_ERROR(panel->dev, "failed to enter sleep mode: %d\n",
> + err);
> + return err;
> + }
> +
> + gpiod_set_value_cansleep(innolux->enable_gpio, 0);
> +
> + /* T8: 80ms - 1000ms */
> + msleep(80);
> +
> + err = regulator_disable(innolux->supply);
> + if (err < 0)
> + return err;
> +
> + innolux->prepared = false;
> +
> + return 0;
> +}
> +
> +static int innolux_panel_prepare(struct drm_panel *panel)
> +{
> + struct innolux_panel *innolux = to_innolux_panel(panel);
> + int err, regulator_err;
> +
> + if (innolux->prepared)
> + return 0;
> +
> + gpiod_set_value_cansleep(innolux->enable_gpio, 0);
> +
> + err = regulator_enable(innolux->supply);
> + if (err < 0)
> + return err;
> +
> + /* T2: 15ms - 1000ms */
> + usleep_range(15000, 16000);
> +
> + gpiod_set_value_cansleep(innolux->enable_gpio, 1);
> +
> + /* T4: 15ms - 1000ms */
> + usleep_range(15000, 16000);
> +
> + err = mipi_dsi_dcs_exit_sleep_mode(innolux->link);
> + if (err < 0) {
> + DRM_DEV_ERROR(panel->dev, "failed to exit sleep mode: %d\n",
> + err);
> + goto poweroff;
> + }
> +
> + /* T6: 120ms - 1000ms*/
> + msleep(120);
> +
> + err = mipi_dsi_dcs_set_display_on(innolux->link);
> + if (err < 0) {
> + DRM_DEV_ERROR(panel->dev, "failed to set display on: %d\n",
> + err);
> + goto poweroff;
> + }
> +
> + /* T7: 5ms */
> + usleep_range(5000, 6000);
> +
> + innolux->prepared = true;
> +
> + return 0;
> +
> +poweroff:
> + regulator_err = regulator_disable(innolux->supply);
> + if (regulator_err)
> + DRM_DEV_ERROR(panel->dev, "failed to disable regulator: %d\n",
> + regulator_err);
> +
> + gpiod_set_value_cansleep(innolux->enable_gpio, 0);
> + return err;
> +}
> +
> +static int innolux_panel_enable(struct drm_panel *panel)
> +{
> + struct innolux_panel *innolux = to_innolux_panel(panel);
> + int ret;
> +
> + if (innolux->enabled)
> + return 0;
> +
> + if (innolux->backlight) {
> + innolux->backlight->props.power = FB_BLANK_UNBLANK;
> + ret = backlight_update_status(innolux->backlight);
> + if (ret) {
> + DRM_DEV_ERROR(panel->drm->dev,
> + "Failed to enable backlight %d\n", ret);
> + return ret;
> + }
> + }
> +
> + innolux->enabled = true;
> +
> + return 0;
> +}
> +
> +static const struct drm_display_mode default_mode = {
> + .clock = 56900,
> + .hdisplay = 768,
> + .hsync_start = 768 + 40,
> + .hsync_end = 768 + 40 + 40,
> + .htotal = 768 + 40 + 40 + 40,
> + .vdisplay = 1024,
> + .vsync_start = 1024 + 20,
> + .vsync_end = 1024 + 20 + 4,
> + .vtotal = 1024 + 20 + 4 + 20,
> + .vrefresh = 60,
> +};
> +
> +static int innolux_panel_get_modes(struct drm_panel *panel)
> +{
> + struct drm_display_mode *mode;
> +
> + mode = drm_mode_duplicate(panel->drm, &default_mode);
> + if (!mode) {
> + DRM_DEV_ERROR(panel->drm->dev, "failed to add mode %ux%ux@%u\n",
> + default_mode.hdisplay, default_mode.vdisplay,
> + default_mode.vrefresh);
> + return -ENOMEM;
> + }
> +
> + drm_mode_set_name(mode);
> +
> + drm_mode_probed_add(panel->connector, mode);
> +
> + panel->connector->display_info.width_mm = 120;
> + panel->connector->display_info.height_mm = 160;
> +
> + return 1;
> +}
> +
> +static const struct drm_panel_funcs innolux_panel_funcs = {
> + .disable = innolux_panel_disable,
> + .unprepare = innolux_panel_unprepare,
> + .prepare = innolux_panel_prepare,
> + .enable = innolux_panel_enable,
> + .get_modes = innolux_panel_get_modes,
> +};
> +
> +static const struct of_device_id innolux_of_match[] = {
> + { .compatible = "innolux,p079zca", },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, innolux_of_match);
> +
> +static int innolux_panel_add(struct innolux_panel *innolux)
> +{
> + struct device *dev = &innolux->link->dev;
> + struct device_node *np;
> + int err;
> +
> + innolux->supply = devm_regulator_get(dev, "power");
> + if (IS_ERR(innolux->supply))
> + return PTR_ERR(innolux->supply);
> +
> + innolux->enable_gpio = devm_gpiod_get_optional(dev, "enable",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(innolux->enable_gpio)) {
> + err = PTR_ERR(innolux->enable_gpio);
> + dev_dbg(dev, "failed to get enable gpio: %d\n", err);
> + innolux->enable_gpio = NULL;
> + }
> +
> + np = of_parse_phandle(dev->of_node, "backlight", 0);
> + if (np) {
> + innolux->backlight = of_find_backlight_by_node(np);
> + of_node_put(np);
> +
> + if (!innolux->backlight)
> + return -EPROBE_DEFER;
> + }
> +
> + drm_panel_init(&innolux->base);
> + innolux->base.funcs = &innolux_panel_funcs;
> + innolux->base.dev = &innolux->link->dev;
> +
> + err = drm_panel_add(&innolux->base);
> + if (err < 0)
> + goto put_backlight;
> +
> + return 0;
> +
> +put_backlight:
> + if (innolux->backlight)
> + put_device(&innolux->backlight->dev);
> +
> + return err;
> +}
> +
> +static void innolux_panel_del(struct innolux_panel *innolux)
> +{
> + if (innolux->base.dev)
> + drm_panel_remove(&innolux->base);
> +
> + if (innolux->backlight)
> + put_device(&innolux->backlight->dev);
> +}
> +
> +static int innolux_panel_probe(struct mipi_dsi_device *dsi)
> +{
> + struct innolux_panel *innolux;
> + int err;
> +
> + dsi->lanes = 4;
> + dsi->format = MIPI_DSI_FMT_RGB888;
> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
> + MIPI_DSI_MODE_LPM;
> +
> + innolux = devm_kzalloc(&dsi->dev, sizeof(*innolux), GFP_KERNEL);
> + if (!innolux)
> + return -ENOMEM;
> +
> + mipi_dsi_set_drvdata(dsi, innolux);
> +
> + innolux->link = dsi;
> +
> + err = innolux_panel_add(innolux);
> + if (err < 0)
> + return err;
> +
> + err = mipi_dsi_attach(dsi);
> + return err;
> +}
> +
> +static int innolux_panel_remove(struct mipi_dsi_device *dsi)
> +{
> + struct innolux_panel *innolux = mipi_dsi_get_drvdata(dsi);
> + int err;
> +
> + err = innolux_panel_unprepare(&innolux->base);
> + if (err < 0)
> + DRM_DEV_ERROR(&dsi->dev, "failed to unprepare panel: %d\n",
> + err);
> +
> + err = innolux_panel_disable(&innolux->base);
> + if (err < 0)
> + DRM_DEV_ERROR(&dsi->dev, "failed to disable panel: %d\n", err);
> +
> + err = mipi_dsi_detach(dsi);
> + if (err < 0)
> + DRM_DEV_ERROR(&dsi->dev, "failed to detach from DSI host: %d\n",
> + err);
> +
> + drm_panel_detach(&innolux->base);
> + innolux_panel_del(innolux);
> +
> + return 0;
> +}
> +
> +static void innolux_panel_shutdown(struct mipi_dsi_device *dsi)
> +{
> + struct innolux_panel *innolux = mipi_dsi_get_drvdata(dsi);
> +
> + innolux_panel_unprepare(&innolux->base);
> + innolux_panel_disable(&innolux->base);
> +}
> +
> +static struct mipi_dsi_driver innolux_panel_driver = {
> + .driver = {
> + .name = "panel-innolux-p079zca",
> + .of_match_table = innolux_of_match,
> + },
> + .probe = innolux_panel_probe,
> + .remove = innolux_panel_remove,
> + .shutdown = innolux_panel_shutdown,
> +};
> +module_mipi_dsi_driver(innolux_panel_driver);
> +
> +MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
> +MODULE_DESCRIPTION("Innolux P079ZCA panel driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.6.3
>
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

\
 
 \ /
  Last update: 2017-03-23 22:14    [W:0.054 / U:0.528 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site