lkml.org 
[lkml]   [2017]   [Mar]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 3/3] extcon: cht-wc: Add Intel Cherry Trail Whiskey Cove PMIC extcon driver
Date
Add a driver for charger detection / control on the Intel Cherrytrail
Whiskey Cove PMIC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
-Improve wait for charger detection loop, use jiffies to get an accurate timeout
-Sort registers by address, remove duplicate definition
-Return IRQ_NONE on interrupt handling errors
-Various small style cleanups
-Fix reporting no charger cable being present when detecting the same
charger type 2 times in a row
-Reset to autonomous / hw-mode on probe-error and on remove
---
drivers/extcon/Kconfig | 7 +
drivers/extcon/Makefile | 1 +
drivers/extcon/extcon-cht-wc.c | 390 +++++++++++++++++++++++++++++++++++++++++
3 files changed, 398 insertions(+)
create mode 100644 drivers/extcon/extcon-cht-wc.c

diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
index 96bbae5..4cace6b 100644
--- a/drivers/extcon/Kconfig
+++ b/drivers/extcon/Kconfig
@@ -52,6 +52,13 @@ config EXTCON_INTEL_INT3496
This ACPI device is typically found on Intel Baytrail or Cherrytrail
based tablets, or other Baytrail / Cherrytrail devices.

+config EXTCON_CHT_WC
+ tristate "Intel Cherrytrail Whiskey Cove PMIC extcon driver"
+ depends on INTEL_SOC_PMIC_CHTWC
+ help
+ Say Y here to enable extcon support for charger detection / control
+ on the Intel Cherrytrail Whiskey Cove PMIC.
+
config EXTCON_MAX14577
tristate "Maxim MAX14577/77836 EXTCON Support"
depends on MFD_MAX14577
diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
index 237ac3f..160f88b 100644
--- a/drivers/extcon/Makefile
+++ b/drivers/extcon/Makefile
@@ -7,6 +7,7 @@ extcon-core-objs += extcon.o devres.o
obj-$(CONFIG_EXTCON_ADC_JACK) += extcon-adc-jack.o
obj-$(CONFIG_EXTCON_ARIZONA) += extcon-arizona.o
obj-$(CONFIG_EXTCON_AXP288) += extcon-axp288.o
+obj-$(CONFIG_EXTCON_CHT_WC) += extcon-cht-wc.o
obj-$(CONFIG_EXTCON_GPIO) += extcon-gpio.o
obj-$(CONFIG_EXTCON_INTEL_INT3496) += extcon-intel-int3496.o
obj-$(CONFIG_EXTCON_MAX14577) += extcon-max14577.o
diff --git a/drivers/extcon/extcon-cht-wc.c b/drivers/extcon/extcon-cht-wc.c
new file mode 100644
index 0000000..9e14972
--- /dev/null
+++ b/drivers/extcon/extcon-cht-wc.c
@@ -0,0 +1,390 @@
+/*
+ * Extcon charger detection driver for Intel Cherrytrail Whiskey Cove PMIC
+ * Copyright (C) 2017 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Based on various non upstream patches to support the CHT Whiskey Cove PMIC:
+ * Copyright (C) 2013-2015 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/extcon.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define CHT_WC_PHYCTRL 0x5e07
+
+#define CHT_WC_CHGRCTRL0 0x5e16
+#define CHT_WC_CHGRCTRL0_CHGRRESET BIT(0)
+#define CHT_WC_CHGRCTRL0_EMRGCHREN BIT(1)
+#define CHT_WC_CHGRCTRL0_EXTCHRDIS BIT(2)
+#define CHT_WC_CHGRCTRL0_SWCONTROL BIT(3)
+#define CHT_WC_CHGRCTRL0_TTLCK_MASK BIT(4)
+#define CHT_WC_CHGRCTRL0_CCSM_OFF_MASK BIT(5)
+#define CHT_WC_CHGRCTRL0_DBPOFF_MASK BIT(6)
+#define CHT_WC_CHGRCTRL0_WDT_NOKICK BIT(7)
+
+#define CHT_WC_CHGRCTRL1 0x5e17
+
+#define CHT_WC_USBSRC 0x5e29
+#define CHT_WC_USBSRC_STS_MASK GENMASK(1, 0)
+#define CHT_WC_USBSRC_STS_SUCCESS 2
+#define CHT_WC_USBSRC_STS_FAIL 3
+#define CHT_WC_USBSRC_TYPE_SHIFT 2
+#define CHT_WC_USBSRC_TYPE_MASK GENMASK(5, 2)
+#define CHT_WC_USBSRC_TYPE_NONE 0
+#define CHT_WC_USBSRC_TYPE_SDP 1
+#define CHT_WC_USBSRC_TYPE_DCP 2
+#define CHT_WC_USBSRC_TYPE_CDP 3
+#define CHT_WC_USBSRC_TYPE_ACA 4
+#define CHT_WC_USBSRC_TYPE_SE1 5
+#define CHT_WC_USBSRC_TYPE_MHL 6
+#define CHT_WC_USBSRC_TYPE_FLOAT_DP_DN 7
+#define CHT_WC_USBSRC_TYPE_OTHER 8
+#define CHT_WC_USBSRC_TYPE_DCP_EXTPHY 9
+
+#define CHT_WC_PWRSRC_IRQ 0x6e03
+#define CHT_WC_PWRSRC_IRQ_MASK 0x6e0f
+#define CHT_WC_PWRSRC_STS 0x6e1e
+#define CHT_WC_PWRSRC_VBUS BIT(0)
+#define CHT_WC_PWRSRC_DC BIT(1)
+#define CHT_WC_PWRSRC_BAT BIT(2)
+#define CHT_WC_PWRSRC_ID_GND BIT(3)
+#define CHT_WC_PWRSRC_ID_FLOAT BIT(4)
+
+enum cht_wc_usb_id {
+ USB_ID_OTG,
+ USB_ID_GND,
+ USB_ID_FLOAT,
+ USB_RID_A,
+ USB_RID_B,
+ USB_RID_C,
+};
+
+/* Strings matching the cht_wc_usb_id enum labels */
+static const char * const usb_id_str[] = {
+ "otg", "gnd", "float", "rid_a", "rid_b", "rid_c" };
+
+enum cht_wc_mux_select {
+ MUX_SEL_PMIC = 0,
+ MUX_SEL_SOC,
+};
+
+static const unsigned int cht_wc_extcon_cables[] = {
+ EXTCON_USB,
+ EXTCON_USB_HOST,
+ EXTCON_CHG_USB_SDP,
+ EXTCON_CHG_USB_CDP,
+ EXTCON_CHG_USB_DCP,
+ EXTCON_CHG_USB_ACA,
+ EXTCON_NONE,
+};
+
+struct cht_wc_extcon_data {
+ struct device *dev;
+ struct regmap *regmap;
+ struct extcon_dev *edev;
+ unsigned int previous_cable;
+ int usb_id;
+};
+
+static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
+{
+ if (ext->usb_id)
+ return ext->usb_id;
+
+ if (pwrsrc_sts & CHT_WC_PWRSRC_ID_GND)
+ return USB_ID_GND;
+ if (pwrsrc_sts & CHT_WC_PWRSRC_ID_FLOAT)
+ return USB_ID_FLOAT;
+
+ /*
+ * Once we have iio support for the gpadc we should read the USBID
+ * gpadc channel here and determine ACA role based on that.
+ */
+ return USB_ID_FLOAT;
+}
+
+static int cht_wc_extcon_get_charger(struct cht_wc_extcon_data *ext)
+{
+ int ret, usbsrc, status;
+ unsigned long timeout;
+
+ /* Charger detection can take upto 600ms, wait 800ms max. */
+ timeout = jiffies + msecs_to_jiffies(800);
+ do {
+ ret = regmap_read(ext->regmap, CHT_WC_USBSRC, &usbsrc);
+ if (ret) {
+ dev_err(ext->dev, "Error reading usbsrc: %d\n", ret);
+ return ret;
+ }
+
+ status = usbsrc & CHT_WC_USBSRC_STS_MASK;
+ if (status == CHT_WC_USBSRC_STS_SUCCESS ||
+ status == CHT_WC_USBSRC_STS_FAIL)
+ break;
+
+ msleep(50); /* Wait a bit before retrying */
+ } while (time_before(jiffies, timeout));
+
+ if (status != CHT_WC_USBSRC_STS_SUCCESS) {
+ if (status == CHT_WC_USBSRC_STS_FAIL)
+ dev_warn(ext->dev, "Could not detect charger type\n");
+ else
+ dev_warn(ext->dev, "Timeout detecting charger type\n");
+ return EXTCON_CHG_USB_SDP; /* Save fallback */
+ }
+
+ usbsrc = (usbsrc & CHT_WC_USBSRC_TYPE_MASK) >> CHT_WC_USBSRC_TYPE_SHIFT;
+ switch (usbsrc) {
+ default:
+ dev_warn(ext->dev, "Unhandled charger type %d\n", ret);
+ /* Fall through treat as SDP */
+ case CHT_WC_USBSRC_TYPE_SDP:
+ case CHT_WC_USBSRC_TYPE_FLOAT_DP_DN:
+ case CHT_WC_USBSRC_TYPE_OTHER:
+ return EXTCON_CHG_USB_SDP;
+ case CHT_WC_USBSRC_TYPE_CDP:
+ return EXTCON_CHG_USB_CDP;
+ case CHT_WC_USBSRC_TYPE_DCP:
+ case CHT_WC_USBSRC_TYPE_DCP_EXTPHY:
+ case CHT_WC_USBSRC_TYPE_MHL: /* MHL2+ delivers upto 2A, treat as DCP */
+ return EXTCON_CHG_USB_DCP;
+ case CHT_WC_USBSRC_TYPE_ACA:
+ return EXTCON_CHG_USB_ACA;
+ }
+}
+
+static void cht_wc_extcon_set_phymux(struct cht_wc_extcon_data *ext, u8 state)
+{
+ int ret;
+
+ ret = regmap_write(ext->regmap, CHT_WC_PHYCTRL, state);
+ if (ret)
+ dev_err(ext->dev, "Error writing phyctrl: %d\n", ret);
+}
+
+/* Small helper to sync EXTCON_CHG_USB_SDP and EXTCON_USB state */
+static void cht_wc_extcon_set_state(struct cht_wc_extcon_data *ext,
+ unsigned int cable, bool state)
+{
+ extcon_set_state_sync(ext->edev, cable, state);
+ if (cable == EXTCON_CHG_USB_SDP)
+ extcon_set_state_sync(ext->edev, EXTCON_USB, state);
+}
+
+static void cht_wc_extcon_pwrsrc_event(struct cht_wc_extcon_data *ext)
+{
+ int ret, pwrsrc_sts, id;
+ unsigned int cable = EXTCON_NONE;
+
+ ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_STS, &pwrsrc_sts);
+ if (ret) {
+ dev_err(ext->dev, "Error reading pwrsrc status: %d\n", ret);
+ return;
+ }
+
+ id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
+ if (id == USB_ID_GND) {
+ /* The 5v boost causes a false VBUS / SDP detect, skip */
+ goto charger_det_done;
+ }
+
+ /* Plugged into a host/charger or not connected? */
+ if (!(pwrsrc_sts & CHT_WC_PWRSRC_VBUS)) {
+ /* Route D+ and D- to PMIC for future charger detection */
+ cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
+ goto set_state;
+ }
+
+ ret = cht_wc_extcon_get_charger(ext);
+ if (ret >= 0)
+ cable = ret;
+
+charger_det_done:
+ /* Route D+ and D- to SoC for the host / gadget controller */
+ cht_wc_extcon_set_phymux(ext, MUX_SEL_SOC);
+
+set_state:
+ if (cable != ext->previous_cable) {
+ cht_wc_extcon_set_state(ext, cable, true);
+ cht_wc_extcon_set_state(ext, ext->previous_cable, false);
+ ext->previous_cable = cable;
+ }
+
+ extcon_set_state_sync(ext->edev, EXTCON_USB_HOST,
+ id == USB_ID_GND || id == USB_RID_A);
+}
+
+static irqreturn_t cht_wc_extcon_isr(int irq, void *data)
+{
+ struct cht_wc_extcon_data *ext = data;
+ int ret, irqs;
+
+ ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_IRQ, &irqs);
+ if (ret) {
+ dev_err(ext->dev, "Error reading irqs: %d\n", ret);
+ return IRQ_NONE;
+ }
+
+ cht_wc_extcon_pwrsrc_event(ext);
+
+ ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ, irqs);
+ if (ret) {
+ dev_err(ext->dev, "Error writing irqs: %d\n", ret);
+ return IRQ_NONE;
+ }
+
+ return IRQ_HANDLED;
+}
+
+/* usb_id sysfs attribute for debug / testing purposes */
+static ssize_t usb_id_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct cht_wc_extcon_data *ext = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%s\n", usb_id_str[ext->usb_id]);
+}
+
+static ssize_t usb_id_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t n)
+{
+ struct cht_wc_extcon_data *ext = dev_get_drvdata(dev);
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(usb_id_str); i++) {
+ if (sysfs_streq(buf, usb_id_str[i])) {
+ dev_info(ext->dev, "New usb_id %s\n", usb_id_str[i]);
+ ext->usb_id = i;
+ cht_wc_extcon_pwrsrc_event(ext);
+ return n;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static DEVICE_ATTR(usb_id, 0644, usb_id_show, usb_id_store);
+
+static int cht_wc_extcon_sw_control(struct cht_wc_extcon_data *ext, bool enable)
+{
+ int ret, mask, val;
+
+ mask = CHT_WC_CHGRCTRL0_SWCONTROL | CHT_WC_CHGRCTRL0_CCSM_OFF_MASK;
+ val = enable ? mask : 0;
+ ret = regmap_update_bits(ext->regmap, CHT_WC_CHGRCTRL0, mask, val);
+ if (ret)
+ dev_err(ext->dev, "Failed setting sw control: %d\n", ret);
+
+ return ret;
+}
+
+static int cht_wc_extcon_probe(struct platform_device *pdev)
+{
+ struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
+ struct cht_wc_extcon_data *ext;
+ int irq, ret;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ ext = devm_kzalloc(&pdev->dev, sizeof(*ext), GFP_KERNEL);
+ if (!ext)
+ return -ENOMEM;
+
+ ext->dev = &pdev->dev;
+ ext->regmap = pmic->regmap;
+ ext->previous_cable = EXTCON_NONE;
+
+ /* Initialize extcon device */
+ ext->edev = devm_extcon_dev_allocate(ext->dev, cht_wc_extcon_cables);
+ if (IS_ERR(ext->edev))
+ return PTR_ERR(ext->edev);
+
+ /* Enable sw control */
+ ret = cht_wc_extcon_sw_control(ext, true);
+ if (ret)
+ return ret;
+
+ /* Register extcon device */
+ ret = devm_extcon_dev_register(ext->dev, ext->edev);
+ if (ret) {
+ dev_err(ext->dev, "Failed to register extcon device\n");
+ goto disable_sw_control;
+ }
+
+ /* Route D+ and D- to PMIC for initial charger detection */
+ cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
+
+ /* Get initial state */
+ cht_wc_extcon_pwrsrc_event(ext);
+
+ ret = devm_request_threaded_irq(ext->dev, irq, NULL, cht_wc_extcon_isr,
+ IRQF_ONESHOT, pdev->name, ext);
+ if (ret) {
+ dev_err(ext->dev, "Failed to request interrupt\n");
+ goto disable_sw_control;
+ }
+
+ /* Unmask irqs */
+ ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ_MASK,
+ (int)~(CHT_WC_PWRSRC_VBUS | CHT_WC_PWRSRC_ID_GND |
+ CHT_WC_PWRSRC_ID_FLOAT));
+ if (ret) {
+ dev_err(ext->dev, "Failed to write the irq-mask: %d\n", ret);
+ goto disable_sw_control;
+ }
+
+ platform_set_drvdata(pdev, ext);
+ device_create_file(ext->dev, &dev_attr_usb_id);
+
+ return 0;
+
+disable_sw_control:
+ cht_wc_extcon_sw_control(ext, false);
+ return ret;
+}
+
+static int cht_wc_extcon_remove(struct platform_device *pdev)
+{
+ struct cht_wc_extcon_data *ext = platform_get_drvdata(pdev);
+
+ device_remove_file(ext->dev, &dev_attr_usb_id);
+ cht_wc_extcon_sw_control(ext, false);
+
+ return 0;
+}
+
+static const struct platform_device_id cht_wc_extcon_table[] = {
+ { .name = "cht_wcove_pwrsrc" },
+ {},
+};
+MODULE_DEVICE_TABLE(platform, cht_wc_extcon_table);
+
+static struct platform_driver cht_wc_extcon_driver = {
+ .probe = cht_wc_extcon_probe,
+ .remove = cht_wc_extcon_remove,
+ .id_table = cht_wc_extcon_table,
+ .driver = {
+ .name = "cht_wcove_pwrsrc",
+ },
+};
+module_platform_driver(cht_wc_extcon_driver);
+
+MODULE_DESCRIPTION("Intel Cherrytrail Whiskey Cove PMIC extcon driver");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_LICENSE("GPL v2");
--
2.9.3
\
 
 \ /
  Last update: 2017-03-20 22:31    [W:0.078 / U:2.096 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site