lkml.org 
[lkml]   [2017]   [Mar]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] drm/tegra: add tiling FB modifiers
On Tue, Nov 08, 2016 at 06:19:01PM +0900, Alexandre Courbot wrote:
> On 11/08/2016 06:07 PM, Erik Faye-Lund wrote:
> > On Tue, Nov 8, 2016 at 8:50 AM, Alexandre Courbot <acourbot@nvidia.com> wrote:
> >> Add FB modifiers to allow user-space to specify that a surface is in one
> >> of the two tiling formats supported by Tegra chips, and add support in
> >> the tegradrm driver to handle them properly. This is necessary for the
> >> display controller to directly display buffers generated by the GPU.
> >>
> >> This feature is intended to replace the dedicated IOCTL enabled
> >> by TEGRA_STAGING and to provide a non-staging alternative to that
> >> solution.
> >>
> >> Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
> >> ---
> >> drivers/gpu/drm/tegra/drm.c | 2 ++
> >> drivers/gpu/drm/tegra/fb.c | 23 +++++++++++++++++++---
> >> include/uapi/drm/drm_fourcc.h | 45 +++++++++++++++++++++++++++++++++++++++++++
> >> 3 files changed, 67 insertions(+), 3 deletions(-)
> >>
> >> diff --git a/drivers/gpu/drm/tegra/drm.c b/drivers/gpu/drm/tegra/drm.c
> >> index a9630c2d6cb3..36b4b30a5164 100644
> >> --- a/drivers/gpu/drm/tegra/drm.c
> >> +++ b/drivers/gpu/drm/tegra/drm.c
> >> @@ -161,6 +161,8 @@ static int tegra_drm_load(struct drm_device *drm, unsigned long flags)
> >> drm->mode_config.max_width = 4096;
> >> drm->mode_config.max_height = 4096;
> >>
> >> + drm->mode_config.allow_fb_modifiers = true;
> >> +
> >> drm->mode_config.funcs = &tegra_drm_mode_funcs;
> >>
> >> err = tegra_drm_fb_prepare(drm);
> >> diff --git a/drivers/gpu/drm/tegra/fb.c b/drivers/gpu/drm/tegra/fb.c
> >> index e6d71fa4028e..2fded58b2ca5 100644
> >> --- a/drivers/gpu/drm/tegra/fb.c
> >> +++ b/drivers/gpu/drm/tegra/fb.c
> >> @@ -52,9 +52,26 @@ int tegra_fb_get_tiling(struct drm_framebuffer *framebuffer,
> >> struct tegra_bo_tiling *tiling)
> >> {
> >> struct tegra_fb *fb = to_tegra_fb(framebuffer);
> >> -
> >> - /* TODO: handle YUV formats? */
> >> - *tiling = fb->planes[0]->tiling;
> >> + uint64_t modifier = fb->base.modifier[0];
> >> +
> >> + switch (fourcc_mod_tegra_mod(modifier)) {
> >> + case NV_FORMAT_MOD_TEGRA_TILED:
> >> + tiling->mode = TEGRA_BO_TILING_MODE_TILED;
> >> + tiling->value = 0;
> >> + break;
> >> +
> >> + case NV_FORMAT_MOD_TEGRA_16BX2_BLOCK(0):
> >> + tiling->mode = TEGRA_BO_TILING_MODE_BLOCK;
> >> + tiling->value = fourcc_mod_tegra_param(modifier);
> >> + if (tiling->value > 5)
> >> + return -EINVAL;
> >
> > Shouldn't this contain some hardware-check for the support? AFAIK, not
> > all Tegras support all block-heights (if even this mode at all?)...
>
> tegra_dc_setup_window does that check later (check the test on
> dc->soc->supports_block_linear). At the moment no error message is
> displayed though (and it seems like we are writing a stale value in
> DC_WIN_BUFFER_ADDR_MODE if the SoC doesn't support block linear and the
> tiling mode is TEGRA_BO_TILING_MODE_BLOCK?)

tegra_plane_atomic_check() has a check for this, as well as an error
message. ->atomic_check() will always run before actually setting the
mode, or applying the plane state, so it effectively guards against a
user specifying a format that the hardware doesn't support.

Thierry
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2017-03-20 18:27    [W:0.043 / U:0.636 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site