lkml.org 
[lkml]   [2017]   [Mar]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 4/5] dt-bindings: auxdisplay: Add bindings for Hitachi HD44780
On Fri, Mar 10, 2017 at 03:15:20PM +0100, Geert Uytterhoeven wrote:
> Add DT bindings for an Hitachi HD44780 Character LCD Controller where
> its M6800 bus interface is connected to GPIOs.
>
> Memory-mapped configurations are not yet supported.
>
> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
> ---
> Memory-mapped configurations can be supported by amending the binding to
> make mandatory either the {data,enable,rs}-gpios properties, or a "reg"
> (and optional "reg-names") property.
>
> As the driver doesn't support this yet, and there are different ways to
> organize the register map (some wirings use different addresses for
> reading and writing, to simplify bus glue logic), this is left for a
> future improvement.
>
> v2:
> - Added rationale below "---".
> ---
> .../devicetree/bindings/auxdisplay/hit,hd44780.txt | 44 ++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/auxdisplay/hit,hd44780.txt
>
> diff --git a/Documentation/devicetree/bindings/auxdisplay/hit,hd44780.txt b/Documentation/devicetree/bindings/auxdisplay/hit,hd44780.txt
> new file mode 100644
> index 0000000000000000..ee4054da458d412f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/auxdisplay/hit,hd44780.txt
> @@ -0,0 +1,44 @@
> +DT bindings for the Hitachi HD44780 Character LCD Controller
> +
> +The Hitachi HD44780 Character LCD Controller is commonly used on character LCDs
> +that can display one or more lines of text. It exposes an M6800 bus interface,
> +which can be used in either 4-bit or 8-bit mode.
> +
> +Required properties:
> + - compatible: Must contain "hit,hd44780",
> + - data-gpios: Must contain an array of either 4 or 8 GPIO specifiers,
> + referring to the GPIO pins connected to the data signal lines DB0-DB7
> + (8-bit mode) or DB4-DB7 (4-bit mode) of the LCD Controller's bus interface,
> + - enable-gpios: Must contain a GPIO specifier, referring to the GPIO pin
> + connected to the "E" (Enable) signal line of the LCD Controller's bus
> + interface,
> + - rs-gpios: Must contain a GPIO specifier, referring to the GPIO pin
> + connected to the "RS" (Register Select) signal line of the LCD Controller's
> + bus interface,
> + - display-height: Height of the display, in character cells,
> + - display-width: Width of the display, in character cells.

display-{width,height}-chars

> +
> +Optional properties:
> + - rw-gpios: Must contain a GPIO specifier, referring to the GPIO pin
> + connected to the "RW" (Read/Write) signal line of the LCD Controller's bus
> + interface,
> + - backlight-gpios: Must contain a GPIO specifier, referring to the GPIO pin
> + used for enabling the LCD's backlight,

Active state?

> + - internal-buffer-width: Internal buffer width (default is 40 for displays
> + with 1 or 2 lines, and display-width for displays with more than 2 lines).
> +
> +Example:
> +
> + auxdisplay {
> + compatible = "hit,hd44780";
> +
> + data-gpios = <&hc595 0 GPIO_ACTIVE_HIGH>,
> + <&hc595 1 GPIO_ACTIVE_HIGH>,
> + <&hc595 2 GPIO_ACTIVE_HIGH>,
> + <&hc595 3 GPIO_ACTIVE_HIGH>;
> + enable-gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
> + rs-gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
> +
> + display-height = <2>;
> + display-width = <16>;
> + };
> --
> 2.7.4
>

\
 
 \ /
  Last update: 2017-03-20 16:24    [W:1.650 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site