lkml.org 
[lkml]   [2017]   [Mar]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [linux-sunxi] [PATCH v3 5/5] ARM: dts: sun8i: h2+: enable USB OTG for Orange Pi Zero board
On Wed, Mar 15, 2017 at 5:09 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
>
> 2017年3月15日 15:16于 Chen-Yu Tsai <wens@csie.org>写道:
>>
>> Hi,
>>
>> On Tue, Mar 7, 2017 at 6:34 AM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
>> > Orange Pi Zero board features a USB OTG port, which has a ID pin, and
>> > can be used to power up the board. However, even if the board is powered
>> > via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
>> > be powered up, thus it's impossible to use it in host mode with simple
>> > OTG cables.
>> >
>> > Add support for it in peripheral mode.
>> >
>> > If someone really want to use it in host mode, the mode of PHY can be
>> > switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
>> > power up external USB devices.
>> >
>> > Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>> > ---
>> > New patch in v3.
>> >
>> > arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 14 ++++++++++++++
>> > 1 file changed, 14 insertions(+)
>> >
>> > diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
>> > index b7ca916d871d..63f819394b98 100644
>> > --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
>> > +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
>> > @@ -96,6 +96,10 @@
>> > };
>> > };
>> >
>> > +&ehci0 {
>> > + status = "okay";
>> > +};
>> > +
>> > &ehci1 {
>> > status = "okay";
>> > };
>> > @@ -132,6 +136,10 @@
>> > bias-pull-up;
>> > };
>> >
>> > +&ohci0 {
>> > + status = "okay";
>> > +};
>> > +
>> > &ohci1 {
>> > status = "okay";
>> > };
>> > @@ -154,7 +162,13 @@
>> > status = "disabled";
>> > };
>> >
>> > +&usb_otg {
>> > + dr_mode = "peripheral";
>> > + status = "okay";
>> > +};
>> > +
>> > &usbphy {
>> > /* USB VBUS is always on */
>>
>> This comment does not match your commit message, which says it's always off.
>
> Oh I should say "USB Type-A port VBUS".

Yes you should probably update that comment, and also mention the OTG port's
VBUS is always off.

ChenYu

>>
>> ChenYu
>>
>> > status = "okay";
>> > + usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
>> > };
>> > --
>> > 2.11.1
>> >
>> > --
>> > You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
>> > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
>> > For more options, visit https://groups.google.com/d/optout.
>>
>> --
>> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
>> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
>> For more options, visit https://groups.google.com/d/optout.
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.

\
 
 \ /
  Last update: 2017-03-20 16:08    [W:0.037 / U:11.632 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site