lkml.org 
[lkml]   [2017]   [Mar]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2] ARM: zynq: Add #io-channel-cells to (x)adc node for iio-hwmon
From
Date
On 16.3.2017 22:20, Lars-Peter Clausen wrote:
> On 03/16/2017 07:06 PM, Michal Simek wrote:
>> On 16.3.2017 17:51, Lars-Peter Clausen wrote:
>>> On 03/16/2017 05:45 PM, Michal Simek wrote:
>>>> On 16.3.2017 17:39, Moritz Fischer wrote:
>>>>> On Thu, Mar 16, 2017 at 9:16 AM, Michal Simek <michal.simek@xilinx.com> wrote:
>>>>>> Hi,
>>>>>>
>>>>>> On 8.3.2017 21:11, Moritz Fischer wrote:
>>>>>>> Fix
>>>>>>>
>>>>>>> OF: /iio_hwmon: could not get #io-channel-cells for
>>>>>>> /amba/adc@f8007100
>>>>>>> OF: /iio_hwmon: could not get #io-channel-cells for
>>>>>>> /amba/adc@f8007100
>>>>>>> OF: /iio_hwmon: could not get #io-channel-cells for
>>>>>>> /amba/adc@f8007100
>>>>>>>
>>>>>>> by adding the #io-channel-cells property.
>>>>>>>
>>>>>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>>>>>> Cc: Michal Simek <michal.simek@xilinx.com>
>>>>>>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>>>>>>> Cc: Julia Cartwright <julia@ni.com>
>>>>>>> Cc: linux-kernel@vger.kernel.org
>>>>>>> Cc: devicetree@vger.kernel.org
>>>>>>> ---
>>>>>>>
>>>>>>> Changes from v1:
>>>>>>> - fix messed up commit message
>>>>>>> ---
>>>>>>> arch/arm/boot/dts/zynq-7000.dtsi | 1 +
>>>>>>> 1 file changed, 1 insertion(+)
>>>>>>>
>>>>>>> diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
>>>>>>> index f3ac9bf..98233a8 100644
>>>>>>> --- a/arch/arm/boot/dts/zynq-7000.dtsi
>>>>>>> +++ b/arch/arm/boot/dts/zynq-7000.dtsi
>>>>>>> @@ -72,6 +72,7 @@
>>>>>>> interrupts = <0 7 4>;
>>>>>>> interrupt-parent = <&intc>;
>>>>>>> clocks = <&clkc 12>;
>>>>>>> + #io-channel-cells = <1>;
>>>>>>> };
>>>>>>>
>>>>>>> can0: can@e0008000 {
>>>>>>>
>>>>>>
>>>>>> I think it will be good to the next step too.
>>>>>> It means also add iio-hwmon node too.
>>>>>>
>>>>>> What do you think?
>>>>>
>>>>> I hadn't put it in there since dts is supposed to describe hw,
>>>>> but obviously putting the actual hwmon in there makes it more useful.
>>>>
>>>> I had one discussion about this with Grant in past and it is common
>>>> mistake. It is simplification of purpose of dts.
>>>>
>>>
>>> If the iio-hwmon binding had gone through review it would have been rejected.
>>
>> Isn't it a time to deprecate it?
>
> Well, it's ABI now and has to stay forever. Deprecating it makes only sense
> if there is a replacement, which there is not. The iio-hwmon bridge has its
> usecases it's just instantiating it via devicetree which is not so nice.
>
>>
>>>
>>>>>
>>>>> I can resubmit with the hwmon node in there.
>>>>
>>>> If you grep kernel tree you will see that others are using it too.
>>>> Also there is accepted binding for that that's why I can't see big
>>>> problem with it.
>>>
>>> Since this is an application specific binding I wouldn't put it in the
>>> generic DT include file. It's a bit like adding a gpio-key binding for each
>>> of the GPIOs just in case somebody wants to use it.
>>
>> psci is system specific too.
>>
>> IIRC this driver for zynq was written by ADI or with ADI help that's why
>> you know much better than I what's the correct configuration.
>>
>> This targets PS IP which should be present in the hw all the time.
>> Not sure if for all configuration but I expect at least the part of it
>> is there all them time.
>>
>> If binding is incorrect then please remove it with removing from all
>> dts/dtsi files which have this. The same is for of probe function in the
>> driver itself.
>> If this is not done then this is just +1 case.
>>
>> If you still insist that we shouldn't do it then please at least extend
>> commit message and put there example how to wire it on zynq.
>
> There is a IIO driver for the XADC, this driver has a userspace interface
> that exposes the measurements provided by the hardware. Using the hwmon
> bridge will expose the same information just through a hwmon interface.
>
> One reason for using the iio-hwmon bridge is because you have a legacy
> application that expects the a hwmon interface. But new applications that
> want to access the XADC should really use the IIO interface if possible.
>
> In my opinion instantiating the hwmon bridge by default will only cause
> confusion. There are now redundant interfaces and users will wonder what is
> the difference between the two. Is it the same data, is it different data?
> Which is the preferred interface? Which one is 'better'?

IMHO this should be covered by documentation. One paragraph in iio-hwmon
binding can have answers for this and it will be very clear what people
should use.

Thanks,
Michal

\
 
 \ /
  Last update: 2017-03-17 07:47    [W:0.095 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site