lkml.org 
[lkml]   [2017]   [Mar]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 13/18] power: supply: add battery driver for AXP20X and AXP22X PMICs
Hi,

On Wed, Mar 15, 2017 at 11:55:32AM +0100, Quentin Schulz wrote:
> The X-Powers AXP20X and AXP22X PMICs can have a battery as power supply.
>
> This patch adds the battery power supply driver to get various data from
> the PMIC, such as the battery status (charging, discharging, full,
> dead), current max limit, current current, battery capacity (in
> percentage), voltage max and min limits, current voltage and battery
> capacity (in Ah).
>
> This battery driver uses the AXP20X/AXP22X ADC driver as PMIC data
> provider.
>
> Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
> Acked-by: Jonathan Cameron <jic23@kernel.org>
> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Acked-by: Chen-Yu Tsai <wens@csie.org>

I think this should be named axp20x-battery-fuel-gauge or just
axp20x-battery. For my own reference:

Acked-by: Sebastian Reichel <sre@kernel.org>

-- Sebastian

> v4:
> - removed useless axp20x_dev variable in struct axp20x_batt_ps,
> - added struct device and maximum constant current charge variables in struct
> axp20x_batt_ps,
> - fixed wrong maximum constant current charge formula for AXP22X (forgot to add
> a custom formula so it was calculated like the AXP209),
> - when a battery node in DT does not have a valid constant current charge or
> there is no battery, the maximum current constant current charge are set to the
> lowest possible value,
> - it is possible to set maximum constant current charge now but a warn message
> is printed when trying to increase it to inform people it is risky,
> - added a check to verify the constant current charge to be set is under the
> maximum allowed,
> - lower the current constant charge current if it is higher than the maximum
> current value to be set,
>
> v3:
> - added axp20x_set_voltage_min_design function so it can be reused,
> - used power_supply_get_battery_info for setting constant charge current
> instead of x-powers,constant-charge-current introduced in v2,
> - used power_supply_get_battery_info for setting voltage min design of
> the battery,
>
> v2:
> - changed BIT(x) to 1 << x when describing bits purpose for which 2 <<
> x or 3 << x exists, to be consistent,
> - switched from POWER_SUPPLY_PROP_CURRENT_MAX to
> POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
> - added POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX to the list of
> readable properties,
> - replaced µ character by a common u for micro units to make checkpatch
> happy,
> - factorized code in axp20x_battery_set_max_voltage,
> - added a axp20x_set_constant_charge_current function to be used when
> setting the value from sysfs and from the DT,
> - removed some dead code,
> - added a DT property to set constant current charge of the battery
> (x-powers,constant-charge-current),
> - migrated to dev_get_regmap instead of manually looking for the regmap
> in the drvdata of the parent,
> - switched from int to uintptr_t cast to make sure the cast is always
>
> for the same size type (make build on 64bits platforms happy mainly),
> drivers/power/supply/Kconfig | 12 +
> drivers/power/supply/Makefile | 1 +
> drivers/power/supply/axp20x_battery.c | 565 ++++++++++++++++++++++++++++++++++
> 3 files changed, 578 insertions(+)
> create mode 100644 drivers/power/supply/axp20x_battery.c
>
> diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
> index da54ac8..8306e98 100644
> --- a/drivers/power/supply/Kconfig
> +++ b/drivers/power/supply/Kconfig
> @@ -232,6 +232,18 @@ config CHARGER_AXP20X
> This driver can also be built as a module. If so, the module will be
> called axp20x_ac_power.
>
> +config BATTERY_AXP20X
> + tristate "X-Powers AXP20X battery driver"
> + depends on MFD_AXP20X
> + depends on AXP20X_ADC
> + depends on IIO
> + help
> + Say Y here to enable support for X-Powers AXP20X PMICs' battery power
> + supply.
> +
> + This driver can also be built as a module. If so, the module will be
> + called axp20x_battery.
> +
> config AXP288_CHARGER
> tristate "X-Powers AXP288 Charger"
> depends on MFD_AXP20X && EXTCON_AXP288
> diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
> index 3789a2c..52dd17d 100644
> --- a/drivers/power/supply/Makefile
> +++ b/drivers/power/supply/Makefile
> @@ -18,6 +18,7 @@ obj-$(CONFIG_TEST_POWER) += test_power.o
>
> obj-$(CONFIG_BATTERY_88PM860X) += 88pm860x_battery.o
> obj-$(CONFIG_BATTERY_ACT8945A) += act8945a_charger.o
> +obj-$(CONFIG_BATTERY_AXP20X) += axp20x_battery.o
> obj-$(CONFIG_CHARGER_AXP20X) += axp20x_ac_power.o
> obj-$(CONFIG_BATTERY_DS2760) += ds2760_battery.o
> obj-$(CONFIG_BATTERY_DS2780) += ds2780_battery.o
> diff --git a/drivers/power/supply/axp20x_battery.c b/drivers/power/supply/axp20x_battery.c
> new file mode 100644
> index 0000000..dcc017a
> --- /dev/null
> +++ b/drivers/power/supply/axp20x_battery.c
> @@ -0,0 +1,565 @@
> +/*
> + * Battery power supply driver for X-Powers AXP20X and AXP22X PMICs
> + *
> + * Copyright 2016 Free Electrons NextThing Co.
> + * Quentin Schulz <quentin.schulz@free-electrons.com>
> + *
> + * This driver is based on a previous upstreaming attempt by:
> + * Bruno Prémont <bonbons@linux-vserver.org>
> + *
> + * This file is subject to the terms and conditions of the GNU General
> + * Public License. See the file "COPYING" in the main directory of this
> + * archive for more details.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/power_supply.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/time.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/consumer.h>
> +#include <linux/mfd/axp20x.h>
> +
> +#define AXP20X_PWR_STATUS_BAT_CHARGING BIT(2)
> +
> +#define AXP20X_PWR_OP_BATT_PRESENT BIT(5)
> +#define AXP20X_PWR_OP_BATT_ACTIVATED BIT(3)
> +
> +#define AXP209_FG_PERCENT GENMASK(6, 0)
> +#define AXP22X_FG_VALID BIT(7)
> +
> +#define AXP20X_CHRG_CTRL1_TGT_VOLT GENMASK(6, 5)
> +#define AXP20X_CHRG_CTRL1_TGT_4_1V (0 << 5)
> +#define AXP20X_CHRG_CTRL1_TGT_4_15V (1 << 5)
> +#define AXP20X_CHRG_CTRL1_TGT_4_2V (2 << 5)
> +#define AXP20X_CHRG_CTRL1_TGT_4_36V (3 << 5)
> +
> +#define AXP22X_CHRG_CTRL1_TGT_4_22V (1 << 5)
> +#define AXP22X_CHRG_CTRL1_TGT_4_24V (3 << 5)
> +
> +#define AXP20X_CHRG_CTRL1_TGT_CURR GENMASK(3, 0)
> +
> +#define AXP20X_V_OFF_MASK GENMASK(2, 0)
> +
> +struct axp20x_batt_ps {
> + struct regmap *regmap;
> + struct power_supply *batt;
> + struct device *dev;
> + struct iio_channel *batt_chrg_i;
> + struct iio_channel *batt_dischrg_i;
> + struct iio_channel *batt_v;
> + /* Maximum constant charge current */
> + unsigned int max_ccc;
> + u8 axp_id;
> +};
> +
> +static int axp20x_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt,
> + int *val)
> +{
> + int ret, reg;
> +
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, &reg);
> + if (ret)
> + return ret;
> +
> + switch (reg & AXP20X_CHRG_CTRL1_TGT_VOLT) {
> + case AXP20X_CHRG_CTRL1_TGT_4_1V:
> + *val = 4100000;
> + break;
> + case AXP20X_CHRG_CTRL1_TGT_4_15V:
> + *val = 4150000;
> + break;
> + case AXP20X_CHRG_CTRL1_TGT_4_2V:
> + *val = 4200000;
> + break;
> + case AXP20X_CHRG_CTRL1_TGT_4_36V:
> + *val = 4360000;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int axp22x_battery_get_max_voltage(struct axp20x_batt_ps *axp20x_batt,
> + int *val)
> +{
> + int ret, reg;
> +
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_CHRG_CTRL1, &reg);
> + if (ret)
> + return ret;
> +
> + switch (reg & AXP20X_CHRG_CTRL1_TGT_VOLT) {
> + case AXP20X_CHRG_CTRL1_TGT_4_1V:
> + *val = 4100000;
> + break;
> + case AXP20X_CHRG_CTRL1_TGT_4_2V:
> + *val = 4200000;
> + break;
> + case AXP22X_CHRG_CTRL1_TGT_4_22V:
> + *val = 4220000;
> + break;
> + case AXP22X_CHRG_CTRL1_TGT_4_24V:
> + *val = 4240000;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int axp20x_get_constant_charge_current(struct axp20x_batt_ps *axp,
> + int *val)
> +{
> + int ret;
> +
> + ret = regmap_read(axp->regmap, AXP20X_CHRG_CTRL1, val);
> + if (ret)
> + return ret;
> +
> + *val &= AXP20X_CHRG_CTRL1_TGT_CURR;
> +
> + if (axp->axp_id == AXP209_ID)
> + *val = *val * 100000 + 300000;
> + else
> + *val = *val * 150000 + 300000;
> +
> + return 0;
> +}
> +
> +static int axp20x_battery_get_prop(struct power_supply *psy,
> + enum power_supply_property psp,
> + union power_supply_propval *val)
> +{
> + struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
> + struct iio_channel *chan;
> + int ret = 0, reg, val1;
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_PRESENT:
> + case POWER_SUPPLY_PROP_ONLINE:
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_OP_MODE,
> + &reg);
> + if (ret)
> + return ret;
> +
> + val->intval = !!(reg & AXP20X_PWR_OP_BATT_PRESENT);
> + break;
> +
> + case POWER_SUPPLY_PROP_STATUS:
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_INPUT_STATUS,
> + &reg);
> + if (ret)
> + return ret;
> +
> + if (reg & AXP20X_PWR_STATUS_BAT_CHARGING) {
> + val->intval = POWER_SUPPLY_STATUS_CHARGING;
> + return 0;
> + }
> +
> + ret = iio_read_channel_processed(axp20x_batt->batt_dischrg_i,
> + &val1);
> + if (ret)
> + return ret;
> +
> + if (val1) {
> + val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
> + return 0;
> + }
> +
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_FG_RES, &val1);
> + if (ret)
> + return ret;
> +
> + /*
> + * Fuel Gauge data takes 7 bits but the stored value seems to be
> + * directly the raw percentage without any scaling to 7 bits.
> + */
> + if ((val1 & AXP209_FG_PERCENT) == 100)
> + val->intval = POWER_SUPPLY_STATUS_FULL;
> + else
> + val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
> + break;
> +
> + case POWER_SUPPLY_PROP_HEALTH:
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_OP_MODE,
> + &val1);
> + if (ret)
> + return ret;
> +
> + if (val1 & AXP20X_PWR_OP_BATT_ACTIVATED) {
> + val->intval = POWER_SUPPLY_HEALTH_DEAD;
> + return 0;
> + }
> +
> + val->intval = POWER_SUPPLY_HEALTH_GOOD;
> + break;
> +
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> + ret = axp20x_get_constant_charge_current(axp20x_batt,
> + &val->intval);
> + if (ret)
> + return ret;
> + break;
> +
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
> + val->intval = axp20x_batt->max_ccc;
> + break;
> +
> + case POWER_SUPPLY_PROP_CURRENT_NOW:
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_INPUT_STATUS,
> + &reg);
> + if (ret)
> + return ret;
> +
> + if (reg & AXP20X_PWR_STATUS_BAT_CHARGING)
> + chan = axp20x_batt->batt_chrg_i;
> + else
> + chan = axp20x_batt->batt_dischrg_i;
> +
> + ret = iio_read_channel_processed(chan, &val->intval);
> + if (ret)
> + return ret;
> +
> + /* IIO framework gives mA but Power Supply framework gives uA */
> + val->intval *= 1000;
> + break;
> +
> + case POWER_SUPPLY_PROP_CAPACITY:
> + /* When no battery is present, return capacity is 100% */
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_PWR_OP_MODE,
> + &reg);
> + if (ret)
> + return ret;
> +
> + if (!(reg & AXP20X_PWR_OP_BATT_PRESENT)) {
> + val->intval = 100;
> + return 0;
> + }
> +
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_FG_RES, &reg);
> + if (ret)
> + return ret;
> +
> + if (axp20x_batt->axp_id == AXP221_ID &&
> + !(reg & AXP22X_FG_VALID))
> + return -EINVAL;
> +
> + /*
> + * Fuel Gauge data takes 7 bits but the stored value seems to be
> + * directly the raw percentage without any scaling to 7 bits.
> + */
> + val->intval = reg & AXP209_FG_PERCENT;
> + break;
> +
> + case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
> + if (axp20x_batt->axp_id == AXP209_ID)
> + return axp20x_battery_get_max_voltage(axp20x_batt,
> + &val->intval);
> + return axp22x_battery_get_max_voltage(axp20x_batt,
> + &val->intval);
> +
> + case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
> + ret = regmap_read(axp20x_batt->regmap, AXP20X_V_OFF, &reg);
> + if (ret)
> + return ret;
> +
> + val->intval = 2600000 + 100000 * (reg & AXP20X_V_OFF_MASK);
> + break;
> +
> + case POWER_SUPPLY_PROP_VOLTAGE_NOW:
> + ret = iio_read_channel_processed(axp20x_batt->batt_v,
> + &val->intval);
> + if (ret)
> + return ret;
> +
> + /* IIO framework gives mV but Power Supply framework gives uV */
> + val->intval *= 1000;
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int axp20x_battery_set_max_voltage(struct axp20x_batt_ps *axp20x_batt,
> + int val)
> +{
> + switch (val) {
> + case 4100000:
> + val = AXP20X_CHRG_CTRL1_TGT_4_1V;
> + break;
> +
> + case 4150000:
> + if (axp20x_batt->axp_id == AXP221_ID)
> + return -EINVAL;
> +
> + val = AXP20X_CHRG_CTRL1_TGT_4_15V;
> + break;
> +
> + case 4200000:
> + val = AXP20X_CHRG_CTRL1_TGT_4_2V;
> + break;
> +
> + default:
> + /*
> + * AXP20x max voltage can be set to 4.36V and AXP22X max voltage
> + * can be set to 4.22V and 4.24V, but these voltages are too
> + * high for Lithium based batteries (AXP PMICs are supposed to
> + * be used with these kinds of battery).
> + */
> + return -EINVAL;
> + }
> +
> + return regmap_update_bits(axp20x_batt->regmap, AXP20X_CHRG_CTRL1,
> + AXP20X_CHRG_CTRL1_TGT_VOLT, val);
> +}
> +
> +static int axp20x_set_constant_charge_current(struct axp20x_batt_ps *axp_batt,
> + int charge_current)
> +{
> + if (charge_current > axp_batt->max_ccc)
> + return -EINVAL;
> +
> + if (axp_batt->axp_id == AXP209_ID)
> + charge_current = (charge_current - 300000) / 100000;
> + else
> + charge_current = (charge_current - 300000) / 150000;
> +
> + if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0)
> + return -EINVAL;
> +
> + return regmap_update_bits(axp_batt->regmap, AXP20X_CHRG_CTRL1,
> + AXP20X_CHRG_CTRL1_TGT_CURR, charge_current);
> +}
> +
> +static int axp20x_set_max_constant_charge_current(struct axp20x_batt_ps *axp,
> + int charge_current)
> +{
> + bool lower_max = false;
> +
> + if (axp->axp_id == AXP209_ID)
> + charge_current = (charge_current - 300000) / 100000;
> + else
> + charge_current = (charge_current - 300000) / 150000;
> +
> + if (charge_current > AXP20X_CHRG_CTRL1_TGT_CURR || charge_current < 0)
> + return -EINVAL;
> +
> + if (axp->axp_id == AXP209_ID)
> + charge_current = charge_current * 100000 + 300000;
> + else
> + charge_current = charge_current * 150000 + 300000;
> +
> + if (charge_current > axp->max_ccc)
> + dev_warn(axp->dev,
> + "Setting max constant charge current higher than previously defined. Note that increasing the constant charge current may damage your battery.\n");
> + else
> + lower_max = true;
> +
> + axp->max_ccc = charge_current;
> +
> + if (lower_max) {
> + int current_cc;
> +
> + axp20x_get_constant_charge_current(axp, &current_cc);
> + if (current_cc > charge_current)
> + axp20x_set_constant_charge_current(axp, charge_current);
> + }
> +
> + return 0;
> +}
> +static int axp20x_set_voltage_min_design(struct axp20x_batt_ps *axp_batt,
> + int min_voltage)
> +{
> + int val1 = (min_voltage - 2600000) / 100000;
> +
> + if (val1 < 0 || val1 > AXP20X_V_OFF_MASK)
> + return -EINVAL;
> +
> + return regmap_update_bits(axp_batt->regmap, AXP20X_V_OFF,
> + AXP20X_V_OFF_MASK, val1);
> +}
> +
> +static int axp20x_battery_set_prop(struct power_supply *psy,
> + enum power_supply_property psp,
> + const union power_supply_propval *val)
> +{
> + struct axp20x_batt_ps *axp20x_batt = power_supply_get_drvdata(psy);
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
> + return axp20x_set_voltage_min_design(axp20x_batt, val->intval);
> +
> + case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
> + return axp20x_battery_set_max_voltage(axp20x_batt, val->intval);
> +
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> + return axp20x_set_constant_charge_current(axp20x_batt,
> + val->intval);
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
> + return axp20x_set_max_constant_charge_current(axp20x_batt,
> + val->intval);
> +
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static enum power_supply_property axp20x_battery_props[] = {
> + POWER_SUPPLY_PROP_PRESENT,
> + POWER_SUPPLY_PROP_ONLINE,
> + POWER_SUPPLY_PROP_STATUS,
> + POWER_SUPPLY_PROP_VOLTAGE_NOW,
> + POWER_SUPPLY_PROP_CURRENT_NOW,
> + POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
> + POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
> + POWER_SUPPLY_PROP_HEALTH,
> + POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
> + POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
> + POWER_SUPPLY_PROP_CAPACITY,
> +};
> +
> +static int axp20x_battery_prop_writeable(struct power_supply *psy,
> + enum power_supply_property psp)
> +{
> + return psp == POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN ||
> + psp == POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN ||
> + psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT ||
> + psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX;
> +}
> +
> +static const struct power_supply_desc axp20x_batt_ps_desc = {
> + .name = "axp20x-battery",
> + .type = POWER_SUPPLY_TYPE_BATTERY,
> + .properties = axp20x_battery_props,
> + .num_properties = ARRAY_SIZE(axp20x_battery_props),
> + .property_is_writeable = axp20x_battery_prop_writeable,
> + .get_property = axp20x_battery_get_prop,
> + .set_property = axp20x_battery_set_prop,
> +};
> +
> +static const struct of_device_id axp20x_battery_ps_id[] = {
> + {
> + .compatible = "x-powers,axp209-battery-power-supply",
> + .data = (void *)AXP209_ID,
> + }, {
> + .compatible = "x-powers,axp221-battery-power-supply",
> + .data = (void *)AXP221_ID,
> + }, { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, axp20x_battery_ps_id);
> +
> +static int axp20x_power_probe(struct platform_device *pdev)
> +{
> + struct axp20x_batt_ps *axp20x_batt;
> + struct power_supply_config psy_cfg = {};
> + struct power_supply_battery_info info;
> +
> + if (!of_device_is_available(pdev->dev.of_node))
> + return -ENODEV;
> +
> + axp20x_batt = devm_kzalloc(&pdev->dev, sizeof(*axp20x_batt),
> + GFP_KERNEL);
> + if (!axp20x_batt)
> + return -ENOMEM;
> +
> + axp20x_batt->dev = &pdev->dev;
> +
> + axp20x_batt->batt_v = devm_iio_channel_get(&pdev->dev, "batt_v");
> + if (IS_ERR(axp20x_batt->batt_v)) {
> + if (PTR_ERR(axp20x_batt->batt_v) == -ENODEV)
> + return -EPROBE_DEFER;
> + return PTR_ERR(axp20x_batt->batt_v);
> + }
> +
> + axp20x_batt->batt_chrg_i = devm_iio_channel_get(&pdev->dev,
> + "batt_chrg_i");
> + if (IS_ERR(axp20x_batt->batt_chrg_i)) {
> + if (PTR_ERR(axp20x_batt->batt_chrg_i) == -ENODEV)
> + return -EPROBE_DEFER;
> + return PTR_ERR(axp20x_batt->batt_chrg_i);
> + }
> +
> + axp20x_batt->batt_dischrg_i = devm_iio_channel_get(&pdev->dev,
> + "batt_dischrg_i");
> + if (IS_ERR(axp20x_batt->batt_dischrg_i)) {
> + if (PTR_ERR(axp20x_batt->batt_dischrg_i) == -ENODEV)
> + return -EPROBE_DEFER;
> + return PTR_ERR(axp20x_batt->batt_dischrg_i);
> + }
> +
> + axp20x_batt->regmap = dev_get_regmap(pdev->dev.parent, NULL);
> + platform_set_drvdata(pdev, axp20x_batt);
> +
> + psy_cfg.drv_data = axp20x_batt;
> + psy_cfg.of_node = pdev->dev.of_node;
> +
> + axp20x_batt->axp_id = (uintptr_t)of_device_get_match_data(&pdev->dev);
> +
> + axp20x_batt->batt = devm_power_supply_register(&pdev->dev,
> + &axp20x_batt_ps_desc,
> + &psy_cfg);
> + if (IS_ERR(axp20x_batt->batt)) {
> + dev_err(&pdev->dev, "failed to register power supply: %ld\n",
> + PTR_ERR(axp20x_batt->batt));
> + return PTR_ERR(axp20x_batt->batt);
> + }
> +
> + if (!power_supply_get_battery_info(axp20x_batt->batt, &info)) {
> + int vmin = info.voltage_min_design_uv;
> + int ccc = info.constant_charge_ua;
> +
> + if (vmin > 0 && axp20x_set_voltage_min_design(axp20x_batt,
> + vmin))
> + dev_err(&pdev->dev,
> + "couldn't set voltage_min_design\n");
> +
> + /* Set max to unverified value to be able to set CCC */
> + axp20x_batt->max_ccc = ccc;
> +
> + if (ccc <= 0 || axp20x_set_constant_charge_current(axp20x_batt,
> + ccc)) {
> + dev_err(&pdev->dev,
> + "couldn't set constant charge current from DT: fallback to minimum value\n");
> + ccc = 300000;
> + axp20x_batt->max_ccc = ccc;
> + axp20x_set_constant_charge_current(axp20x_batt, ccc);
> + }
> + }
> +
> + /*
> + * Update max CCC to a valid value if battery info is present or set it
> + * to current register value by default.
> + */
> + axp20x_get_constant_charge_current(axp20x_batt,
> + &axp20x_batt->max_ccc);
> +
> + return 0;
> +}
> +
> +static struct platform_driver axp20x_batt_driver = {
> + .probe = axp20x_power_probe,
> + .driver = {
> + .name = "axp20x-battery-power-supply",
> + .of_match_table = axp20x_battery_ps_id,
> + },
> +};
> +
> +module_platform_driver(axp20x_batt_driver);
> +
> +MODULE_DESCRIPTION("Battery power supply driver for AXP20X and AXP22X PMICs");
> +MODULE_AUTHOR("Quentin Schulz <quentin.schulz@free-electrons.com>");
> +MODULE_LICENSE("GPL");
> --
> 2.9.3
>
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2017-03-16 00:43    [W:1.958 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site