lkml.org 
[lkml]   [2017]   [Mar]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] ARM: dts: BCM5301X: Add support for Linksys EA9500
From
Date
On 03/15/2017 01:18 PM, Vivek Unune wrote:
> Thanks Florian.
>
> Let me try this out. First I'll try to figure out how to add a mdio node.
>
> Over the weekend I was trying enable DSA driver, but did not see DSA
> under network. I'm using LEDE source with kernel 4.9. Nor did I see it
> when I tried 'make kernel_menuconfig'

(please don't top post on public mailing lists)

You need to enable SWITCHDEV to have DSA. AFAIR SWITCHDEV may depend on
EXPERT/EXPERIMENTAL as of 4.9 (or that was before).

>
> Thanks again.
>
> On Wed, Mar 15, 2017 at 3:49 PM, Florian Fainelli
> <florian.fainelli@broadcom.com> wrote:
>> On 03/15/2017 12:34 PM, Vivek Unune wrote:
>>> Andrew,
>>>
>>> I'm not entirely sure. But here is what I observed.
>>>
>>> Boot loader sets up both the switches. And I can use all 8 ports of the
>>> router when I boot Lede. Only the internal swich is detected and
>>> configurable via swconfig tool
>>> Internal switch is connected to CPU via port 5 same as Netgear R8000.
>>> The other bit here is that I looked through the GPL source and gpio pin
>>> 10 is labeled as EA9500_RST2LANSW_GPIO10_PIN/ResetSwitch. So when I
>>> performed a robo reset of the pin and 5 (labeled 1 thru 5 on the unit)
>>> of the 8 physical ports stopped working (no packets).
>>>
>>> If the external switch were to be connect via dedicated ethernet
>>> interface it should have shown up during the probe. Is in't it?
>>
>> Not necessarily, and probably not with LEDE which would treat the
>> external 53125 as a dumb switch and not even see it. With a mainline
>> kernel and the B53 DSA driver you would be able to represent both
>> switches in Device Tree and describe how they are cascading from each other.
>>
>> The potential Device Tree changes could look like this (based on your
>> explanation, but I am not sure) for your platform, assuming the 53125 is
>> actually exposing the front panel ports and that we did introduce a
>> "mdio" node which would be required to expose the external BCM53125 switch.
>>
>>
>> /* There is no MDIO node, there should be one */
>> &mdio {
>> status = "okay";
>>
>> switch@30 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> reset-gpios = <&gpio 10>;
>> reset-names = "robo_reset";
>>
>> ports {
>> #address-cells = <1>;
>> #size-cells = <0>;
>>
>> port@0 {
>> reg = <0>;
>> label = "lan1";
>> };
>>
>> port@1 {
>> reg = <1>;
>> label = "lan2";
>> };
>>
>> port@2 {
>> reg = <2>;
>> label = "lan3";
>> };
>>
>> port@3 {
>> reg = <3>;
>> label = "lan1";
>> };
>>
>> port@4 {
>> reg = <4>;
>> label = "wan";
>> };
>>
>> port@5 {
>> reg = <5>;
>> label = "cpu";
>> ethernet = <&sw0port8>;
>> fixed-link {
>> speed = <1000>;
>> full-duplex;
>> };
>> };
>> };
>> };
>> };
>>
>> &srab {
>> status = "okay";
>>
>> ports {
>> #address-cells = <1>;
>> #size-cells = <0>;
>>
>> port@5 {
>> reg = <5>;
>> label = "cpu";
>> ethernet = <&gmac0>;
>> fixed-link {
>> speed = <1000>;
>> full-duplex;
>> };
>> };
>>
>> sw0port8: port@8 {
>> reg = <8>;
>> label = "extswitch";
>>
>> fixed-link {
>> speed = <1000>;
>> full-duplex;
>> };
>> };
>> };
>> };
>>
>>>
>>> Thanks,
>>>
>>> Vivek
>>>
>>>
>>> On Wed, Mar 15, 2017 at 2:52 PM Andrew Lunn <andrew@lunn.ch
>>> <mailto:andrew@lunn.ch>> wrote:
>>>
>>> Hi Vivek
>>>
>>> > - It has two switches in order to support 8 lan ports. Internal
>>> switch is
>>> > BCM53012. The external switch BCM53125 currently works as "dumb
>>> switch"
>>>
>>> Do you know how the second switch is connected? Is it cascaded off the
>>> internal switch? Or does it have a dedicated Ethernet interface?
>>>
>>> Thanks
>>> Andrew
>>>
>>
>>
>> --
>> Florian


--
Florian

\
 
 \ /
  Last update: 2017-03-15 22:19    [W:0.073 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site