lkml.org 
[lkml]   [2017]   [Feb]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v6 4/6] i2c: designware: introducing I2C_SLAVE definitions
Date
- Definitions were added to core library
- A example was added to designware-core.txt Documentation that shows
how the slave can be setup using DTS

SLAVE related definitions were added to the core of the controller.

Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
V5->V6
- Included an example of use in the device tree binding document

.../devicetree/bindings/i2c/i2c-designware.txt | 16 +++++++++-
drivers/i2c/busses/i2c-designware-core.h | 35 ++++++++++++++++++++--
2 files changed, 48 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
index fee26dc3e858..c6f1d9a63d18 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
@@ -20,7 +20,7 @@ Optional properties :
- i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds.
This value which is by default 300ns is used to compute the tHIGH period.

-Example :
+Examples :

i2c@f0000 {
#address-cells = <1>;
@@ -43,3 +43,17 @@ Example :
i2c-sda-falling-time-ns = <300>;
i2c-scl-falling-time-ns = <300>;
};
+
+ i2c@01120000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2000 0x100>;
+ clock-frequency = <400000>;
+ clocks = <&i2cclk>;
+ interrupts = <0>;
+
+ eeprom@64 {
+ compatible = "linux,slave-24c02";
+ reg = <0x40000064>;
+ };
+ };
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index 8e6b80ab84d1..7e4b2bdc10f0 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -1,5 +1,5 @@
/*
- * Synopsys DesignWare I2C adapter driver (master only).
+ * Synopsys DesignWare I2C adapter driver.
*
* Based on the TI DAVINCI I2C adapter driver.
*
@@ -36,15 +36,20 @@
#define DW_IC_CON_SPEED_FAST 0x4
#define DW_IC_CON_SPEED_HIGH 0x6
#define DW_IC_CON_SPEED_MASK 0x6
+#define DW_IC_CON_10BITADDR_SLAVE 0x8
#define DW_IC_CON_10BITADDR_MASTER 0x10
#define DW_IC_CON_RESTART_EN 0x20
#define DW_IC_CON_SLAVE_DISABLE 0x40
+#define DW_IC_CON_STOP_DET_IFADDRESSED 0x80
+#define DW_IC_CON_TX_EMPTY_CTRL 0x100
+#define DW_IC_CON_RX_FIFO_FULL_HLD_CTRL 0x200

/*
* Registers offset
*/
#define DW_IC_CON 0x0
#define DW_IC_TAR 0x4
+#define DW_IC_SAR 0x8
#define DW_IC_DATA_CMD 0x10
#define DW_IC_SS_SCL_HCNT 0x14
#define DW_IC_SS_SCL_LCNT 0x18
@@ -75,6 +80,7 @@
#define DW_IC_SDA_HOLD 0x7c
#define DW_IC_TX_ABRT_SOURCE 0x80
#define DW_IC_ENABLE_STATUS 0x9c
+#define DW_IC_CLR_RESTART_DET 0xa8
#define DW_IC_COMP_PARAM_1 0xf4
#define DW_IC_COMP_VERSION 0xf8
#define DW_IC_SDA_HOLD_MIN_VERS 0x3131312A
@@ -93,15 +99,22 @@
#define DW_IC_INTR_STOP_DET 0x200
#define DW_IC_INTR_START_DET 0x400
#define DW_IC_INTR_GEN_CALL 0x800
+#define DW_IC_INTR_RESTART_DET 0x1000

#define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \
DW_IC_INTR_TX_ABRT | \
DW_IC_INTR_STOP_DET)
#define DW_IC_INTR_MASTER_MASK (DW_IC_INTR_DEFAULT_MASK | \
DW_IC_INTR_TX_EMPTY)
+#define DW_IC_INTR_SLAVE_MASK (DW_IC_INTR_DEFAULT_MASK | \
+ DW_IC_INTR_RX_DONE | \
+ DW_IC_INTR_RX_UNDER | \
+ DW_IC_INTR_RD_REQ)
+
#define DW_IC_STATUS_ACTIVITY 0x1
#define DW_IC_STATUS_TFE BIT(2)
#define DW_IC_STATUS_MASTER_ACTIVITY BIT(5)
+#define DW_IC_STATUS_SLAVE_ACTIVITY BIT(6)

#define DW_IC_SDA_HOLD_RX_SHIFT 16
#define DW_IC_SDA_HOLD_RX_MASK GENMASK(23, DW_IC_SDA_HOLD_RX_SHIFT)
@@ -123,6 +136,12 @@
#define TIMEOUT 20 /* ms */

/*
+ * operation modes
+ */
+#define DW_IC_MASTER 0
+#define DW_IC_SLAVE 1
+
+/*
* hardware abort codes from the DW_IC_TX_ABRT_SOURCE register
*
* only expected abort codes are listed here
@@ -139,6 +158,9 @@
#define ABRT_10B_RD_NORSTRT 10
#define ABRT_MASTER_DIS 11
#define ARB_LOST 12
+#define ABRT_SLAVE_FLUSH_TXFIFO 13
+#define ABRT_SLAVE_ARBLOST 14
+#define ABRT_SLAVE_RD_INTX 15

#define DW_IC_TX_ABRT_7B_ADDR_NOACK (1UL << ABRT_7B_ADDR_NOACK)
#define DW_IC_TX_ABRT_10ADDR1_NOACK (1UL << ABRT_10ADDR1_NOACK)
@@ -151,6 +173,9 @@
#define DW_IC_TX_ABRT_10B_RD_NORSTRT (1UL << ABRT_10B_RD_NORSTRT)
#define DW_IC_TX_ABRT_MASTER_DIS (1UL << ABRT_MASTER_DIS)
#define DW_IC_TX_ARB_LOST (1UL << ARB_LOST)
+#define DW_IC_RX_ABRT_SLAVE_RD_INTX (1UL << ABRT_SLAVE_RD_INTX)
+#define DW_IC_RX_ABRT_SLAVE_ARBLOST (1UL << ABRT_SLAVE_ARBLOST)
+#define DW_IC_RX_ABRT_SLAVE_FLUSH_TXFIFO (1UL << ABRT_SLAVE_FLUSH_TXFIFO)

#define DW_IC_TX_ABRT_NOACK (DW_IC_TX_ABRT_7B_ADDR_NOACK | \
DW_IC_TX_ABRT_10ADDR1_NOACK | \
@@ -196,7 +221,11 @@
* @acquire_lock: function to acquire a hardware lock on the bus
* @release_lock: function to release a hardware lock on the bus
* @pm_runtime_disabled: true if pm runtime is disabled
- *
+ * @dynamic_tar_update_enabled: true if dynamic TAR update is enabled
+ * @disable: function to disable the controller
+ * @disable_int: function to disable all interrupts
+ * @init: function to initialize the I2C hardware
+ * @mode: operation mode - I2C slave or I2C master
* HCNT and LCNT parameters can be used if the platform knows more accurate
* values than the one computed based only on the input clock frequency.
* Leave them to be %0 if not used.
@@ -206,6 +235,7 @@ struct dw_i2c_dev {
void __iomem *base;
struct completion cmd_complete;
struct clk *clk;
+ struct i2c_client *slave;
u32 (*get_clk_rate_khz) (struct dw_i2c_dev *dev);
struct dw_pci_controller *controller;
int cmd_err;
@@ -225,6 +255,7 @@ struct dw_i2c_dev {
struct i2c_adapter adapter;
u32 functionality;
u32 master_cfg;
+ u32 slave_cfg;
unsigned int tx_fifo_depth;
unsigned int rx_fifo_depth;
int rx_outstanding;
--
2.11.0

\
 
 \ /
  Last update: 2017-02-15 13:24    [W:1.566 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site