lkml.org 
[lkml]   [2017]   [Dec]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 07/12] dt-bindings: Document the Rockchip MIPI RX D-PHY bindings
On Wed, Dec 06, 2017 at 07:19:34PM +0800, Jacob Chen wrote:
> From: Jacob Chen <jacob2.chen@rock-chips.com>
>
> Add DT bindings documentation for Rockchip MIPI D-PHY RX
>
> Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
> ---
> .../bindings/media/rockchip-mipi-dphy.txt | 71 ++++++++++++++++++++++
> 1 file changed, 71 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/rockchip-mipi-dphy.txt
>
> diff --git a/Documentation/devicetree/bindings/media/rockchip-mipi-dphy.txt b/Documentation/devicetree/bindings/media/rockchip-mipi-dphy.txt
> new file mode 100644
> index 000000000000..cef9450db051
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/rockchip-mipi-dphy.txt
> @@ -0,0 +1,71 @@
> +Rockchip SoC MIPI RX D-PHY
> +-------------------------------------------------------------
> +
> +Required properties:
> +
> +- compatible: value should be one of the following
> + "rockchip,rk3288-mipi-dphy";
> + "rockchip,rk3399-mipi-dphy";

Drop the ';'

> +- rockchip,grf: GRF regs.
> +- bus-width : maximum number of data lanes supported (SoC specific);
> +- clocks : list of clock specifiers, corresponding to entries in
> + clock-names property;
> +- clock-names: required clock name.
> +
> +The device node should contain two 'port' child node, according to the bindings
> +defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
> +The first port should be connected to sensor nodes, and the second port should be
> +connected to isp node. The following are properties specific to those nodes.

Need to list how many endpoints if there are more than 1.

> +
> +endpoint node
> +-------------
> +
> +- data-lanes : (required) an array specifying active physical MIPI-CSI2
> + data input lanes and their mapping to logical lanes; the
> + array's content is unused, only its length is meaningful;
> +
> +Device node example
> +-------------------
> +
> + mipi_dphy_rx0: mipi-dphy-rx0 {
> + compatible = "rockchip,rk3399-mipi-dphy";
> + clocks = <&cru SCLK_MIPIDPHY_REF>,
> + <&cru SCLK_DPHY_RX0_CFG>,
> + <&cru PCLK_VIO_GRF>;
> + clock-names = "dphy-ref", "dphy-cfg", "grf";
> + power-domains = <&power RK3399_PD_VIO>;
> + bus-width = <4>;

rockchip,grf?

No other registers? Can you just make this a child of the grf block with
a proper reg property for the range of dphy registers?

> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mipi_in_wcam: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&wcam_out>;
> + data-lanes = <1 2>;
> + };
> + mipi_in_ucam: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&ucam_out>;
> + data-lanes = <1>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + dphy_rx0_out: endpoint@0 {
> + reg = <0>;

Don't need reg and everything associated with it if there's only 1
endpoint.

> + remote-endpoint = <&isp0_mipi_in>;
> + };
> + };
> + };
> + };
> \ No newline at end of file

Please fix.

Rob

\
 
 \ /
  Last update: 2017-12-08 00:27    [W:0.462 / U:0.828 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site