lkml.org 
[lkml]   [2017]   [Dec]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH net-next v3 1/4] phylib: Add device reset delay support
From
Date
Hi Geert,

On 12/05/2017 02:54 PM, Geert Uytterhoeven wrote:
> Hi Richard,
>
> On Tue, Dec 5, 2017 at 2:25 PM, Richard Leitner <dev@g0hl1n.net> wrote:
>> From: Richard Leitner <richard.leitner@skidata.com>
>>
>> Some PHYs need a minimum time after the reset gpio was asserted and/or
>> deasserted. To ensure we meet these timing requirements add two new
>> optional devicetree parameters for the phy: reset-delay-us and
>> reset-post-delay-us.
>
> Thanks for your patch!
>
>> This patch depends on the "phylib: Add device reset GPIO support" patch
>> submitted by Geert Uytterhoeven/Sergei Shtylyov, see:
>> https://patchwork.kernel.org/patch/10090149/
>
> The above paragraph belongs under the "---" line below, as it is not intended
> to be preserved in the eternal git history.

Ok. Thanks. That makes sense. I'll take it into account for v4.

>
>> Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
>
> Although I have a few suggestions below:

Thank you for your review and suggestions (they make the code look way
more neater). I'll adapt v4 accordingly.

>
>> --- a/drivers/net/phy/mdio_device.c
>> +++ b/drivers/net/phy/mdio_device.c
>> @@ -118,8 +119,16 @@ EXPORT_SYMBOL(mdio_device_remove);
>>
>> void mdio_device_reset(struct mdio_device *mdiodev, int value)
>> {
>> - if (mdiodev->reset)
>> - gpiod_set_value(mdiodev->reset, value);
>> + if (!mdiodev->reset)
>> + return;
>> +
>> + gpiod_set_value(mdiodev->reset, value);
>> +
>> + if (value && mdiodev->reset_delay)
>> + usleep_range(mdiodev->reset_delay, mdiodev->reset_delay + 100);
>> + else if (!value && mdiodev->reset_post_delay)
>> + usleep_range(mdiodev->reset_post_delay,
>> + mdiodev->reset_post_delay + 100);
>
> I think this can be written simpler using e.g.:
>
> unsigned int delay;
>
> ...
> delay = value ? mdiodev->reset_delay : mdiodev->reset_post_delay;
> if (delay)
> usleep_range(delay, delay + 100);
>
> Perhaps the range extension should be relative, e.g.
> "delay + min(delay / 10, 100)"?
>
>> --- a/drivers/of/of_mdio.c
>> +++ b/drivers/of/of_mdio.c
>> @@ -77,6 +77,14 @@ static int of_mdiobus_register_phy(struct mii_bus *mdio,
>> if (of_property_read_bool(child, "broken-turn-around"))
>> mdio->phy_ignore_ta_mask |= 1 << addr;
>>
>> + if (of_property_read_u32(child, "reset-delay-us",
>> + &phy->mdio.reset_delay))
>> + phy->mdio.reset_delay = 0;
>> +
>> + if (of_property_read_u32(child, "reset-post-delay-us",
>> + &phy->mdio.reset_post_delay))
>> + phy->mdio.reset_post_delay = 0;
>
> If of_property_read_u32() fails, it doesn't write to its output parameter.
> As the structure should be zeroed during allocation, you can just write:
>
> of_property_read_u32(child, "reset-delay-us", &phy->mdio.reset_delay);
> of_property_read_u32(child, "reset-post-delay-us",
> &phy->mdio.reset_post_delay);

\
 
 \ /
  Last update: 2017-12-05 16:07    [W:0.056 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site