lkml.org 
[lkml]   [2017]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH V8 2/3] OPP: Introduce "required-opp" property
On 18 December 2017 at 11:21, Viresh Kumar <viresh.kumar@linaro.org> wrote:
> Devices have inter-dependencies some times. For example a device that
> needs to run at 800 MHz, needs another device (e.g. Its power domain) to
> be configured at a particular operating performance point.
>
> This patch introduces a new property "required-opp" which can be present
> directly in a device's node (if it doesn't need to change its OPPs), or
> in device's OPP nodes. More details on the property can be seen in the
> binding itself.
>
> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
> ---
> Documentation/devicetree/bindings/opp/opp.txt | 8 +++
> .../devicetree/bindings/power/power_domain.txt | 59 ++++++++++++++++++++++
> 2 files changed, 67 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt
> index a3953a1bb1a1..4e4f30288c8b 100644
> --- a/Documentation/devicetree/bindings/opp/opp.txt
> +++ b/Documentation/devicetree/bindings/opp/opp.txt
> @@ -159,6 +159,14 @@ properties.
>
> - status: Marks the node enabled/disabled.
>
> +- required-opp: This contains phandle to an OPP node in another device's OPP
> + table. It may contain an array of phandles, where each phandle points to an
> + OPP of a different device. It should not contain multiple phandles to the OPP
> + nodes in the same OPP table. This specifies the minimum required OPP of the
> + device(s), whose OPP's phandle is present in this property, for the
> + functioning of the current device at the current OPP (where this property is
> + present).
> +
> Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together.
>
> / {
> diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt
> index 61549840ab3b..f824763b202e 100644
> --- a/Documentation/devicetree/bindings/power/power_domain.txt
> +++ b/Documentation/devicetree/bindings/power/power_domain.txt
> @@ -126,4 +126,63 @@ The node above defines a typical PM domain consumer device, which is located
> inside a PM domain with index 0 of a power controller represented by a node
> with the label "power".
>
> +Optional properties:
> +- required-opp: This contains phandle to an OPP node in another device's OPP
> + table. It may contain an array of phandles, where each phandle points to an
> + OPP of a different device. It should not contain multiple phandles to the OPP
> + nodes in the same OPP table. This specifies the minimum required OPP of the
> + device(s), whose OPP's phandle is present in this property, for the
> + functioning of the current device at the current OPP (where this property is
> + present).
> +
> +Example:
> +- OPP table for domain provider that provides two domains.
> +
> + domain0_opp_table: opp_table0 {
> + compatible = "operating-points-v2";
> +
> + domain0_opp_0: opp-1000000000 {
> + opp-hz = /bits/ 64 <1000000000>;
> + opp-microvolt = <975000 970000 985000>;
> + };
> + domain0_opp_1: opp-1100000000 {
> + opp-hz = /bits/ 64 <1100000000>;
> + opp-microvolt = <1000000 980000 1010000>;
> + };
> + };
> +
> + domain1_opp_table: opp_table1 {
> + compatible = "operating-points-v2";
> +
> + domain1_opp_0: opp-1200000000 {
> + opp-hz = /bits/ 64 <1200000000>;
> + opp-microvolt = <975000 970000 985000>;
> + };
> + domain1_opp_1: opp-1300000000 {
> + opp-hz = /bits/ 64 <1300000000>;
> + opp-microvolt = <1000000 980000 1010000>;
> + };
> + };
> +
> + parent: power-controller@12340000 {

Nitpick: Could you please change "parent" to "power", to be consistent
with earlier examples.

> + compatible = "foo,power-controller";
> + reg = <0x12340000 0x1000>;
> + #power-domain-cells = <1>;
> + operating-points-v2 = <&domain0_opp_table>, <&domain1_opp_table>;
> + };
> +
> + leaky-device0@12350000 {
> + compatible = "foo,i-leak-current";
> + reg = <0x12350000 0x1000>;
> + power-domains = <&parent 0>;
> + required-opp = <&domain0_opp_0>;
> + };
> +
> + leaky-device1@12350000 {
> + compatible = "foo,i-leak-current";
> + reg = <0x12350000 0x1000>;
> + power-domains = <&parent 1>;
> + required-opp = <&domain1_opp_1>;
> + };
> +
> [1]. Documentation/devicetree/bindings/power/domain-idle-state.txt
> --
> 2.15.0.194.g9af6a3dea062
>


Besides the nitpick, feel free to add:

Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>

Kind regards
Uffe

\
 
 \ /
  Last update: 2017-12-20 09:24    [W:0.063 / U:16.368 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site