lkml.org 
[lkml]   [2017]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] usb: host: Implement workaround for Erratum A-009611
On Mon, Dec 11, 2017 at 03:15:37AM +0000, Yinbo Zhu wrote:
>
>
> -----Original Message-----
> From: Felipe Balbi [mailto:felipe.balbi@linux.intel.com]
> Sent: Friday, December 08, 2017 6:44 PM
> To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>; Yinbo Zhu <yinbo.zhu@nxp.com>
> Cc: Mathias Nyman <mathias.nyman@intel.com>; open list:DESIGNWARE USB3 DRD IP DRIVER <linux-usb@vger.kernel.org>; open list:DESIGNWARE USB3 DRD IP DRIVER <linux-omap@vger.kernel.org>; open list <linux-kernel@vger.kernel.org>; Xiaobo Xie <xiaobo.xie@nxp.com>; Jerry Huang <jerry.huang@nxp.com>; Ran Wang <ran.wang_1@nxp.com>
> Subject: Re: [PATCH v2] usb: host: Implement workaround for Erratum A-009611
>
>
> >Hi,
>
> >Greg Kroah-Hartman <gregkh@linuxfoundation.org> writes:
> > On Fri, Dec 08, 2017 at 05:49:41PM +0800, yinbo.zhu@nxp.com wrote:
> >> From: "yinbo.zhu" <yinbo.zhu@nxp.com>
> >>
> >> Description: This is a occasional problem where the software
> >
> > No need for a "Description:" word. That's just assumed here, right?
>
> I will remove "Description:" thanks.
> >> issues an End Transfer command while a USB transfer is in progress,
> >> resulting in the TxFIFO being flushed when the lower layer is
> >> waiting for data,causing the super speed (SS) transmit to get blocked.
> >> If the End Transfer command is issued on an IN endpoint to flush out
> >> the pending transfers when the same IN endpoint is doing transfers on
> >> the USB, then depending upon the timing of the End Transfer (and the
> >> resulting internal FIFO flush),the lower layer (U3PTL/U3MAC) could
> >> get stuck waiting for data indefinitely. This blocks the transmission
> >> path on the SS, and no DP/ACK/ERDY/DEVNOTIF packets can be sent from
> >> the device.
> >> Impact: If this issue happens and the transmission gets blocked, then
> >> the USB host aborts and resets/re-enumerates the device.
> >> This unblocks the transmitt engine and the device functions normally.
> >>
> >> Workaround: Software must wait for all existing TRBs to complete
> >> before issuing End transfer command.
> >>
> >> Configs Affected:
> >> LS1088-48A-R1.0, LS2081A-R1.1, LS2088-48A-R1.0, LS2088-48A-R1.1,
> >> LX2160-2120-2080A-R1.
> >
> > What are these Configs? That doesn't seem to match up with anything
> > that is in the kernel tree that I can see.
>
> These configs is soc information, I don't enable it on these platform dts.
> Although the erratum issue can't be reproduced.

I do not understand what this means, please explain it a bit better.

thanks,

greg k-h

\
 
 \ /
  Last update: 2017-12-11 08:35    [W:0.067 / U:0.556 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site