lkml.org 
[lkml]   [2017]   [Nov]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ARM: dts: imx6sx-sdb: Add DRM panel, power-enable and backlight support
Date
It is preferred to use the panel compatible string rather than passing 
the LCD timming in the device tree.

So pass the "sii,43wvf1g" compatible string, a new driver for the Seiko
Panel, which describes the parallel LCD.

This new driver needs two power supply, so pass 'dvdd-supply' and
'avdd-supply', which makes the kernel to turn on the LCD on is own.

Also, pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
---
arch/arm/boot/dts/imx6sx-sdb.dtsi | 49 ++++++++++++++++++++-------------------
1 file changed, 25 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi
index da81552..3a597a4 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi
@@ -24,7 +24,7 @@
reg = <0x80000000 0x40000000>;
};

- backlight {
+ backlight_display: backlight-display {
compatible = "pwm-backlight";
pwms = <&pwm3 0 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -129,6 +129,14 @@
regulator-max-microvolt = <3300000>;
gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
};
+
+ reg_lcd_5v: regulator@7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "lcd-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
};

sound {
@@ -146,6 +154,19 @@
mux-int-port = <2>;
mux-ext-port = <6>;
};
+
+ panel {
+ compatible = "sii,43wvf1g";
+ backlight = <&backlight_display>;
+ dvdd-supply = <&reg_lcd_3v3>;
+ avdd-supply = <&reg_lcd_5v>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
};

&audmux {
@@ -215,31 +236,11 @@
&lcdif1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd>;
- lcd-supply = <&reg_lcd_3v3>;
- display = <&display0>;
status = "okay";

- display0: display0 {
- bits-per-pixel = <16>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33500000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <89>;
- hfront-porch = <164>;
- vback-porch = <23>;
- vfront-porch = <10>;
- hsync-len = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
};
};
};
--
2.7.4
\
 
 \ /
  Last update: 2017-11-30 14:02    [W:0.052 / U:0.512 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site