lkml.org 
[lkml]   [2017]   [Oct]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v7] PCI: Workaround wrong flags completions for IDT switch
This patch is word wrapped and doesn't apply.

On Mon, Sep 18, 2017 at 04:05:45PM -0400, James Puthukattukaran wrote:
> Subject: [PATCH v7] PCI: Workaround wrong flags completions for IDT switch
> From: James Puthukattukaran <james.puthukattukaran@oracle.com>
>
> The IDT switch incorrectly flags an ACS source violation on a read config
> request to an end point device on the completion (IDT 89H32H8G3-YC,
> errata #36) even though the PCI Express spec states that completions are
> never affected by ACS source violation (PCI Spec 3.1, Section

s/PCI Spec 3.1/PCIe r3.1/

> 6.12.1.1). Here's
> the specific copy of the errata text
>
> "Item #36 - Downstream port applies ACS Source Validation to Completions
> Section 6.12.1.1 of the PCI Express Base Specification 3.1 states
> that completions are never affected
> by ACS Source Validation. However, completions received by a
> downstream port of the PCIe switch from a device that has not yet
> captured a PCIe bus number are incorrectly dropped by ACS source
> validation by the switch downstream port.
>
> Workaround: Issue a CfgWr1 to the downstream device before issuing
> the first CfgRd1 to the device.
> This allows the downstream device to capture its bus number; ACS
> source validation no longer stops
> completions from being forwarded by the downstream port. It has been
> observed that Microsoft Windows implements this workaround already;
> however, some versions of Linux and other operating systems may not. "
>
> The suggested workaround by IDT is to issue a configuration write to the
> downstream device before issuing the first config read. This allows the
> downstream device to capture its bus number, thus avoiding the ACS
> violation on the completion. In order to make sure that the device is ready
> for config accesses, we do what is currently done in making config reads
> till it succeeds and then do the config write as specified by the errata.
> However, to avoid hitting the errata issue when doing config reads, we
> disable ACS SV around this process.
>
> The patch does the following -
>
> 1. Disable ACS source violation if enabled.
> 2. Wait for config space access to become available by reading vendor id
> 3. Do a config write to the end point (errata workaround)
> 4. Enable ACS source validation (if it was enabled to begin with)
>
> Signed-off-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
> Signed-off-by: Yinghai Lu <yinghai@kernel.org>
>
> --
>
> -v2: move workaround to pci_bus_read_dev_vendor_id() from
> pci_bus_check_dev()
> and move enable_acs_sv to drivers/pci/pci.c -- by Yinghai
> -v3: add bus->self check for root bus and virtual bus for sriov vfs.
> -v4: only do workaround for IDT switches
> -v5: tweak pci_std_enable_acs_sv to deal with unimplemented SV
> -v6: Added errata verbiage verbatim and resolved patch format issues
> -v7: changed int to bool for found and idt_workaround declarations. Also
> added bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=196979

Thanks for the bugzilla. The URL needs to be in the changelog, i.e., above
the "--". It should go just before the Signed-off-by lines.
>
>
> drivers/pci/pci.c | 40 ++++++++++++++++++++++++++++++++++++++++
> drivers/pci/pci.h | 1 +
> drivers/pci/probe.c | 42 ++++++++++++++++++++++++++++++++++++++++--
> 3 files changed, 81 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
> index 6078dfc..4bca302 100644
> --- a/drivers/pci/pci.c
> +++ b/drivers/pci/pci.c
> @@ -2857,6 +2857,46 @@ static bool pci_acs_flags_enabled(struct
> pci_dev *pdev, u
> 16 acs_flags)
> }
>
> /**
> + * pci_std_enable_acs_sv - enable/disable ACS source validation if
> supported
> + * by the switch
> + * @dev - pcie switch/RP
> + * @enable - enable (1) or disable (0) source validation
> + *
> + * Returns : < 0 on failure (if SV capability is not implemented)
> + * previous acs_sv state (0 or 1)
> + */
> +int pci_std_enable_acs_sv(struct pci_dev *dev, bool enable)
> +{
> + int pos;
> + u16 cap;
> + u16 ctrl;
> + int retval;
> +
> + pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ACS);
> + if (!pos)
> + return -ENODEV;
> +
> + pci_read_config_word(dev, pos + PCI_ACS_CAP, &cap);
> +
> + if (!(cap & PCI_ACS_SV))
> + return -ENODEV;
> +
> + pci_read_config_word(dev, pos + PCI_ACS_CTRL, &ctrl);
> +
> + retval = !!(ctrl & cap & PCI_ACS_SV);
> + if (enable)
> + ctrl |= (cap & PCI_ACS_SV);
> + else
> + ctrl &= ~(cap & PCI_ACS_SV);
> +
> + pci_write_config_word(dev, pos + PCI_ACS_CTRL, ctrl);
> +
> + return retval;
> +}
> +
> +
> +
> +/**
> * pci_acs_enabled - test ACS against required flags for a given device
> * @pdev: device to test
> * @acs_flags: required PCI ACS flags
> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
> index a6560c9..9d9a365 100644
> --- a/drivers/pci/pci.h
> +++ b/drivers/pci/pci.h
> @@ -339,6 +339,7 @@ static inline resource_size_t
> pci_resource_alignment(struct
> pci_dev *dev,
> }
>
> void pci_enable_acs(struct pci_dev *dev);
> +int pci_std_enable_acs_sv(struct pci_dev *dev, bool enable);
>
> #ifdef CONFIG_PCIE_PTM
> void pci_ptm_init(struct pci_dev *dev);
> diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
> index ff94b69..0aa6e02 100644
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -1945,8 +1945,8 @@ static bool pci_bus_wait_crs(struct pci_bus
> *bus, int devf
> n, u32 *l,
> return true;
> }
>
> -bool pci_bus_read_dev_vendor_id(struct pci_bus *bus, int devfn, u32 *l,
> - int timeout)
> +static bool __pci_bus_read_dev_vendor_id(struct pci_bus *bus, int devfn,
> + u32 *l, int timeout)
> {
> if (pci_bus_read_config_dword(bus, devfn, PCI_VENDOR_ID, l))
> return false;
> @@ -1961,6 +1961,44 @@ bool pci_bus_read_dev_vendor_id(struct
> pci_bus *bus, int
> devfn, u32 *l,
>
> return true;
> }
> +
> +
> +bool pci_bus_read_dev_vendor_id(struct pci_bus *bus, int devfn, u32 *l,
> + int crs_timeout)
> +{
> + bool found;
> + int enable = -1;
> + bool idt_workaround = (bus->self && (bus->self->vendor == PCI_VENDOR_ID_
> IDT));
> + /*
> + * Some IDT switches flag an ACS violation for config reads
> + * even though the PCI spec allows for it (PCIe 3.1, 6.1.12.1)
> + * It flags it because the bus number is not properly set in the
> + * completion. The workaround is to do a dummy write to properly
> + * latch number once the device is ready for config operations
> + */
> +
> + if (idt_workaround)
> + enable = pci_std_enable_acs_sv(bus->self, false);
> +
> + found = __pci_bus_read_dev_vendor_id(bus, devfn, l, crs_timeout);
> +
> + /*
> + * The fact that we can read the vendor id indicates that the device
> + * is ready for config operations. Do the write as part of the errata
> + * workaround.
> + */
> + if (idt_workaround) {
> + if (found)
> + pci_bus_write_config_word(bus, devfn, PCI_VENDOR_ID, 0);
> + if (enable > 0)
> + pci_std_enable_acs_sv(bus->self, enable);
> + }
> +
> + return found;

Man, this is UGLY. Ugly, ugly, ugly.

Can you do this as an early quirk on the IDT switch? That would at
least get this out of the main enumeration path.

The problem seems to be with config reads to devices below the IDT
switch. We discover the switch before discovering devices below the
switch. So if we have an early quirk that applies to
PCI_VENDOR_ID_IDT devices, the quirk should run for the switch before
we do anything with the children. The quirk could disable ACS SV, do
config writes to each possible child, and re-enable ACS SV.

> +}
> +
> +
> +
> EXPORT_SYMBOL(pci_bus_read_dev_vendor_id);
>
> /*
>

\
 
 \ /
  Last update: 2017-10-11 21:26    [W:0.253 / U:0.952 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site